5-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver 5% Dimming
369793f 2 04.01.16
Specifications
Regulatory Approvals
• Lutron® Quality Systems registered to ISO 9001.2008.
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20.
• Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV.
• FCC Part 15 compliant for commercial applications at
120 –277 V~.
• UL® 8750 recognized.
• Class 2 output.
Performance
• Dimming Range: 100% to 5%
1
• Dimming method: constant-current reduction, refer to
Lutron® Application Note #360 for details.
• Operating Voltage: 120 V~ to 277 V~ at 50 / 60 Hz
• Lifetime: 50,000 hours @ t
c
= 167 °F (75 °C)
2
• Patented thermal foldback protection.
• LED lighting turns on to any dimmed level without
flashing to full brightness.
• Non-volatile memory restores all driver settings after
power failure.
• Standby power consumption: < 0.2 W at 120 V~ and
< 0.3 W typical at 277 V~.
• For Power Factor (PF) and Line current Total Harmonic
Distortion (THD), see Model Numbers table.
• Open-circuit protected output.
• Short-circuit and overload-protected output.
• Device turn-on time: < 100 ms from electronic off and
< 500 ms from power off.
• Class 2 output designed to withstand hot swap.
Environmental
• Sound rated: inaudible in 27 dBA ambient.
• Relative Humidity: maximum 90% non-condensing.
• Operating Ambient Temperature: t
a
= 32 °F to 122 °F
(0 °C to 50 °C).
3
Driver Wiring and Mounting
• Driver is grounded by a mounting screw to the
grounded fixture or by terminal connection.
• Terminal blocks on the driver accept one solid wire per
terminal from 18 AWG to 16 AWG
(0.75 mm
2
to 1.5 mm
2
).
• Fixture must be grounded in accordance with local
and national electrical codes.
• Maximum driver-to-LED light engine wire length for:
Wire Gauge
Maximum Lead Length
200 mA to 700 mA 710 mA to 1.50 A
18 AWG (0.75mm
2
) 30 ft (9 m) 15 ft (4.5 m)
16 AWG (1.5mm
2
) 35 ft (10.5 m) 25 ft (7.5 m)
14 AWG (2.5mm
2
)* 50 ft (15 m) 40 ft (12 m)
12 AWG (4.0mm
2
)* 100 ft (30 m) 60 ft (18 m)
* Terminal blocks on the drivers accept only solid 18 or 16 AWG (0.75 mm
2
to 1.5 mm
2
) wire. To use wire gauges larger than the terminal blocks’
rated gauge of 18 AWG to 16 AWG (0.75 mm
2
to 1.5 mm
2
), refer to the
Terminal Wiring Gauges diagram on Page 6. Connect up to 3 ft (0.9 m)
of 18 AWG to 16 AWG (0.75 mm
2
to 1.5 mm
2
) wire to the LED driver
terminal blocks, then connect 14 AWG to 12 AWG (2.5 mm
2
to
4.0 mm
2
) up to the length allowed in the above table.
1
Light output at 5% depends on the efficacy of the light engine used with the driver.
2
Installer is responsible for ensuring that the driver calibration point does not exceed the maximum rated temperature.
3
Where t
a
is the temperature of the air directly surrounding the driver.
