Preset Dimming Controls
369316d 6 01.17.20
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
Wireless Control Unit with DALI (CE)
Accessory Controls: Contact Closure Input/Output
Interface (QSE-IO)
• Recalls preset light levels for the following set of scenes
on the GRAFIK Eye QS:
Scenes 1-4 and Off Scenes 9-12 and Off
Scenes 5-8 and Off Scenes 13-16 and Off
• Sequence scenes 5-16, Enable/Disable Zone Lockout,
Enable/Disable Scene Lockout, Enable/Disable Panic
Mode, Enable/Disable Timeclock.
• Occupancy Sensors. An individual input counts as
one occupancy sensor for the GRAFIK Eye QS. Each
input can be assigned to either Scene Control or Zone
Control (please refer to the Occupancy Sensor(s) section
of this guide).
• Zone Toggle. Allows an input to toggle one or more
zones between programmable preset level(s) and off.
• Shade Output mode. A Shade Column on the
GRAFIK Eye QS can be linked to control outputs 1-3
and/or outputs 4-5 on the QSE-IO.
Accessory Controls:
DMX Output Interface (QSE-CI-DMX)
• Any zone on the GRAFIK Eye QS control unit can be
mapped to any single DMX512 Channel.
• Any zone on the GRAFIK Eye QS control unit can be
simultaneously mapped to any three DMX512 channels
(providing RGB/CMY control).
• DMX loads cannot be used with daylighting.
Accessory Controls: Ethernet and RS232 Interface
(QSE-CI-NWK-E)
• Allows for monitoring and control of the outputs and local
scenes of the GRAFIK Eye QS.
Accessory Controls: QS Keyswitch Wallstations
(QSWS2-KS)
• Recalls preset light levels for any two scenes
including Off
• Allows fine-tuning (raise/lower level) of a zone or group
of zones
• Starts/Stops scene sequencing (Scenes 1-4 or
Scenes 5-16)
• Enables/Disables Timeclock
• Enables/Disables occupancy sensors
• Enables/Disabled daylight sensors
• Allows toggle of Zone(s) to a preset level and off
• Enables/Disables panic mode
• Starts/Stops afterhours mode
Accessory Controls: Pico Wireless Control
(QSR8P models)
• The Pico Wireless Control is battery powered. It can control
GRAFIK Eye QS wireless control units within a 10 m
(32 ft) range (20 m [65 ft] in open air). It provides the
following features:
– Control of one or more zones on the GRAFIK Eye QS
Wireless control unit: turns zone(s) on or off, raises/lowers
zone(s), allows programmable light levels for each button,
and goes to user-programmable preset level
– Control of one or more scenes on the GRAFIK Eye QS
Wireless control unit: the Pico® wireless control can
access any three sequential scenes (1 through 16), or any
two sequential scenes and Off; and can raise and lower
lighting levels.
Note: “Unaffected” is not a valid level for Pico zone
programming.
Accessory Controls: QS Sensor Module (QSM3)
• The QS Sensor Module provides a means to link wired
or wireless occupancy sensors or daylight sensors, Pico
controls, and wired infrared sensors to a GRAFIK Eye QS
control unit via the wired QS link.
– Occupancy sensors wired (or wirelessly linked) to a QS
Sensor Module can be used by one or more GRAFIK Eye
QS control units on the wired link.
– Daylight sensors wired (or wirelessly linked) to a
QS Sensor Module can be used by one or more
GRAFIK Eye QS control units on the wired link.
– Pico wireless controls can control either one or more
zones or scenes on the GRAFIK Eye QS.
– Pico wired controls can be used, when connected to
a QS Sensor Module, to control one or more zones or
scenes on the GRAFIK Eye QS control unit.
– Infrared sensors can control either one or more zones
or scenes on the GRAFIK Eye QS. Functionality varies;
refer to the documentation for the QS Sensor Module for
details.
Specifications
