Preset Dimming Controls
369313i 6 07.11.19
Job Name:
Job Number:
Model Numbers:
PageSPECIFICATION SUBMITTAL
Wireless Control Unit
Accessory Controls: seeTouch QS Wallstations
(QSWS2)
• Wired seeTouch QS wallstations provide the
following features:
– Access to one or more of the 16 scenes on the
GRAFIK Eye QS Wireless control unit
– Zone toggle, partitioning, sequencing, fine tune,
panic mode, and timeclock enable/disable
– Contact closure inputs
– Certain functions are only available on specific
wallstation configurations. Refer to the seeTouch QS
specification submittal.
Wireless RF Compatibility
• Features Lutron proprietary Clear Connect RF Technology
• Operates in the 434 MHz band
• Compatible with other Lutron wireless products / systems,
such as:
– Pico wireless control (P/N QSR4P or MRF2)
– Radio Powr Savr occupancy / vacancy / daylight sensors
(P/N LRF2-)
– RadioRA 2 wireless system
– Sivoia QS wireless products
– Other GRAFIK Eye QS wireless control units
(P/N QSGRJ-)
Accessory Controls: Pico Wireless Control
(PJ models)
• The Pico Wireless Control is battery powered. It can control
GRAFIK Eye QS wireless control units within a
30 ft (10 m) range (60 ft [20 m] in open air). It provides the
following features:
– Control of one or more zones on the GRAFIK Eye
QS Wireless control unit: turns zone(s) on or off,
raises / lowers zone(s), allows programmable light levels
for each button, and goes to user-programmable
preset level
– Control of one or more scenes on the GRAFIK Eye
QS Wireless control unit: the Pico wireless control can
access any three sequential scenes (1 through 16), or
any two sequential scenes and Off; and can raise and
lower lighting levels.
Note: “Unaffected” is not a valid level for Pico zone
programming.
Accessory Controls: QS Sensor Module (QSM2)
• The QS Sensor Module provides a means to link wired
or wireless occupancy sensors or daylight sensors, Pico
controls, and wired infrared sensors to a GRAFIK Eye QS
control unit via the wired QS link.
– Occupancy sensors wired (or wirelessly linked) to
a QSSensor Module can be used by one or more
GRAFIKEye QS control units on the wired link.
– Daylight sensors wired (or wirelessly linked) to a
QS Sensor Module can be used by one or more
GRAFIKEye QS control units on the wired link.
– Pico wireless controls can control either one or more
zones or scenes on the GRAFIK Eye QS control unit.
– Pico wired controls can be used, when connected to
a QS Sensor Module, to control one or more zones or
scenes on the GRAFIK Eye QS control unit.
– Infrared sensors can control either one or more zones or
scenes on the GRAFIK Eye QS control unit. Functionality
varies; refer to the documentation for the QS Sensor
Module for details.
Accessory Controls: Contact Closure Input / Output
Interface (QSE-IO)
• Recalls preset light levels for the following set of scenes on
the GRAFIK Eye QS control unit:
– Scenes 1– 4 and Off – Scenes 9 –12 and Off
– Scenes 5 – 8 and Off – Scenes 13 –16 and Off
• Sequence scenes 5 –16, Enable / Disable Zone Lockout,
Enable / Disable Scene Lockout, Enable / Disable Panic
Mode, Enable / Disable Timeclock.
• Occupancy Sensors. An individual input counts as
1occupancy sensor for the GRAFIK Eye QS control unit.
Each input can be assigned to either Scene Control or
Zone Control (please refer to the Occupancy Sensor(s)
section of this guide).
• Zone Toggle. Allows an input to toggle one or more zones
between programmable preset level(s) and off.
• Shade Output mode. A Shade Column on the GRAFIK Eye
QS control unit can be linked to control outputs 1– 3
and / or outputs 4 – 5 on the QSE-IO.
Accessory Controls:
DMX Output Interface (QSE-CI-DMX)
• Any zone on the GRAFIK Eye QS control unit can be
mapped to any single DMX512 Channel.
• Any zone on the GRAFIK Eye QS control unit can be
simultaneously mapped to any three DMX512 channels
(providing RGB/CMY control).
• DMX loads cannot be used with daylighting.
Specifications (continued)
