Fillable Swpm (Lutron Electronics, Inc.)

Fill Online, Printable, Fillable, Blank Swpm (Lutron Electronics, Inc.) Form

Use Fill to complete blank online LUTRON ELECTRONICS, INC. pdf forms for free. Once completed you can sign your fillable form or send for signing. All forms are printable and downloadable.

Swpm (Lutron Electronics, Inc.)

On average this form takes 14 minutes to complete

The Swpm (Lutron Electronics, Inc.) form is 8 pages long and contains:

  • 0 signatures
  • 0 check-boxes
  • 56 other fields

Country of origin: US
File type: PDF

Use our library of forms to quickly fill and sign your Lutron Electronics, Inc. forms online.

BROWSE LUTRON ELECTRONICS, INC. FORMS

Related forms
Fill has a huge library of thousands of forms all set up to be filled in easily and signed.
Fill in your chosen form
Sign the form using our drawing tool
Send to someone else to fill in and sign.
find another form
 
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 1 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Model Number
PHPM-SW-DV-WH
Capacity
16 A
Control Power
120 V
Switching Power Module
Description
• Provides capability for a zone on a GRAFIK Eye
control unit (or other product) to switch a fully
loaded circuit of lighting.
• May be used to switch incandescent, electronic
low-voltage, magnetic low-voltage, HID,
fluorescent ballasts, and neon/cold cathode
lighting sources.
• Utilizes Softswitch® arcless switching technology.
• Provides power and switching for one zone.
• Up to 3 power modules may be wired on a single
GRAFIK Eye zone.
• Model available for 120 V control power.
• Model available for 120 - 277 V load power.
Works with 120 V versions of:
• Lutron® 3-wire fluorescent dimmers (consult
Lutron for Vierti®); see approved list in the
dimmers & switches specification guide at www.
lutron.com
• GRAFIK Eye QS control units
• GRAFIK Eye 3000 Series control units
• LP, LCP, and GP dimming panels
• HomeWorks® remote power panels
Model and Capacities
Load Power
120 - 277 V
1
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 2 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Power
• Control / load power:
120 V / 120 - 277 V
50 / 60 Hz, phase-to-neutral.
• Load (output) power: Phase independent of control unit.
Sources/Load Types
• Switches the following load types:
– Incandescent (tungsten)
– Halogen
– Magnetic low-voltage transformer (iron core)
– Electronic (solid-state) low-voltage transformer.
– Magnetic and electronic fluorescent dimming ballasts
– Neon/cold-cathode
– HID
• Motors:
– 1/2 HP at 277 V
– 1/3 HP at 120 V
• May be used with GFI/AFI breaker protected loads.
Key Design Features
• Patented Softswitch® technology.
• Two LEDs on front of unit provide diagnostic information
(visible when faceplate is removed).
Terminals
Accept up to two 12 AWG (2.5 mm
2
) wires.
Environment
• 32 to 104 °F (0 to 40 °C). Relative humidity less than 90% non-condensing.
• Indoor use only.
• Maximum heat output of module: 15 BTU/hour.
Mounting
• Surface or recess mount.
• Power module is UL tested and approved for use in spaces designed for
environmental air handling.
Specifications
2
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 3 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
• Mount in 2-gang U.S. wallbox 3.5 in
(89 mm) deep or 4 x 4 in (102 x 102 mm)
junction box 2.1 in deep (53 mm).
• Indoors only.
• Mount only where ambient temperature is
32 to 104 °F (0 to 40 °C).
• Allow 4.5 in (114 mm) above and below
unit and between faceplates when
mounting several in a vertical layout.
• Mount so line (mains) voltage wiring is at
least 6 ft (1.8 m) from sound or electronic
equipment and wiring.
• Mount within 7° of true vertical.
Mount to 4 x 4 in (102 x 102 mm), 2.1 in (53 mm) deep
U.S. junction box
Mount to 2-gang U.S. wallbox
Dimensions and Mounting
6.3 in
(160 mm)
0.4 in (10 mm)
Mount to 4 x 4 in (102 x 102 mm), 2.1 in (53 mm) deep
U.S. junction box with barrier
(for 277 V
loads if required by local electrical code)
1.2 in (30.5 mm)
5.1 in (129.5 mm)
Barrier
3
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 4 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
• Pull 12 AWG (2.5 mm
2
) copper (Cu) wires (75 °C/167 °F minimum) for input power and load circuit.
• Strip 1/2 in (12 mm) insulation from wires before connecting.
• Run separate neutral for load circuit - no common neutrals.
• May be used with GFI breaker protected loads. Load circuit wiring (from GFI breaker to power module to
load) must be run in its own non-metallic conduit, or nuisance tripping may occur. Maximum 100 ft (30.5
m) between power module and load.
• May be used with AFI breaker protected loads. Maximum load on AFI circuit is 1000 W. Exceeding 1000 W
may cause nuisance tripping of AFI breaker.
Note: The power modules may be on the same
circuit as the control unit only if the total load does
not exceed the rating of the breaker.
Wiring
Single Power Feed
1 2 3 4 5 6 L N
H/L
N
SH
H/L
N
Load
120 V
GRAFIK Eye QS
Zone in
Control Neutral
Wire to appropriate
zone
Legend
H/L Hot/Live
N Neutral
SH Switched Hot
DH Dimmed Hot
Ground
Not Used
Circuit breaker
120 V
{
4
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 5 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Multiple Power Feeds
Wiring
The load breaker may be on a different
phase than the control breaker.
1 2 3 4 5 6 L N
H/L
N
SH
H/L
N
N
H/L
Load
GRAFIK Eye QS
Zone in
Control Neutral
Wire to appropriate
zone
Legend
H/L Hot/Live
N Neutral
SH Switched Hot
DH Dimmed Hot
Ground
Not Used
Load breaker
Control breaker
120 V
}
120 - 277 V
Load wiring
{
5
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 6 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Wiring Multiple Power Modules to a Single GRAFIK Eye® Zone
Shown with separate feeds for control and loads. All breakers must be turned off prior to
installing or servicing the modules. Up to 3 power modules may be wired to a single zone.
1 2 3 4 5 6 L N
H/L
N
SH
H/L
N
H/L
N
H/L
N
H/L
N
H/L
N
N
H/L
SH
SH
Load
GRAFIK Eye QS
Zone in
Control Neutral
Wire to appropriate zone
Load breaker
Load
Zone in
Control Neutral
Load breaker
Load
Zone in
Control Neutral
Load breaker
Control breaker
Load wiring
1
for Power
Module #1
{
Load wiring
1
for Power
Module #2
{
Load wiring
1
for Power
Module #3
{
1
Load feed: 120 - 277 V for PHPM-SW-DV-WH
120 V
}
6
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 7 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Note: The power module may be on the same circuit/control
zone as the control device only if the total load does not
exceed the rating of the breaker (120 V only).
Multilocation Wiring
H/L
H/L
N
N
SH
Load
Legend
H/L Hot/Live
N Neutral
SH Switched Hot
DH Dimmed Hot
Ground
Not Used
Circuit breaker
{
3-wire
fluorescent
dimmer
120 V
(main
dimmer)
369357 Rev. A 7 11.19.10
3-wire
fluorescent
dimmer
120 V
(accessory/
companion
dimmer or
3-way switch)
H/L 120 V
N
Load
wiring
(see
Note
below)
Note:
1
Load feed: 120 - 277 V for PHPM-SW-DV-WH
SH
(red wire)
Cap off
DH
(yellow
or orange
wire)
Zone in
Control Neutral
For specific wire colors, see the wallbox lighting controls
catalog at www.lutron.com/wallbox catalog
7
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369357 Rev. A 8 11.19.10
Power Modules
Switching Power Module
GRAFIK Eye®
Wiring a Power Module to an LP, LCP, GP, or HomeWorks® Panel
Up to three switching power modules may be wired to an output of a 120 V LP or LCP panel. The load
type for the output must be set as non-dim load type on the panel’s circuit selector (for an LP or GP panel),
controller (for an LCP panel), or HomeWorks software (for a HomeWorks panel).
DH
DH
DH
DH
H
N
N
N
N
N
H/L
N
SH
H/L
N
Load
(1) 14 to 10 AWG
(2.0 to 4.0 mm
2
)
(1) 14 to 10 AWG
(2.0 to 4.0 mm
2
)
Zone In
Control
Neutral
Dimmed
Hot
Neutral
120 V Branch Circuit
Breakers
Neutral Lug
Neutral (1) 14 to 2/0 AWG
(2.0 to 70 mm
2
)
Power (Hot/Live)
(3) 14 to 2/0 AWG (2.0 to 70 mm
2
)
1
120 - 277 V if used with
PHPM-SW-DV-WH power module
Load
wiring
1
{
Wire to appropriate output
8
Download
Save PDF to desktop
Email
Email completed PDF
Send for Signing
Email for others to sign
Print
Print document
Choose a Field
Click on a field and
select the person that should complete it
Want to add a signature?
You can add a signature field
and assign it to someone else
to sign
Choose a Field
Click on a field and
select the person that should complete it

Swpm (Lutron Electronics, Inc.)

This document is locked as it has been sent for signing.

You have successfully completed this document.

Other parties need to complete fields in the document. You will recieve an email notification when the document has been completed by all parties.

This document has been signed by all parties.

Completed 18 July 2020

Message

View Audit Log
Print With Audit Log
Duplicate Document