Fillable Hi 220 240 (Lutron Electronics, Inc.)

Fill Online, Printable, Fillable, Blank Hi 220 240 (Lutron Electronics, Inc.) Form

Use Fill to complete blank online LUTRON ELECTRONICS, INC. pdf forms for free. Once completed you can sign your fillable form or send for signing. All forms are printable and downloadable.

Hi 220 240 (Lutron Electronics, Inc.)

On average this form takes 11 minutes to complete

The Hi 220 240 (Lutron Electronics, Inc.) form is 6 pages long and contains:

  • 0 signatures
  • 0 check-boxes
  • 42 other fields

Country of origin: US
File type: PDF

Use our library of forms to quickly fill and sign your Lutron Electronics, Inc. forms online.

BROWSE LUTRON ELECTRONICS, INC. FORMS

Related forms
Fill has a huge library of thousands of forms all set up to be filled in easily and signed.
Fill in your chosen form
Sign the form using our drawing tool
Send to someone else to fill in and sign.
find another form
 
3-Wire Control, 220/240 Volt
T-8 Linear, T-4 Quad Tube and
T-5 Twin Tube Lamps
DESCRIPTION
• Continuous, flicker-free, 100%-1% dimming to meet the needs
of the most demanding architectural lighting designs
• 3-wire line-voltage control technology for most consistent
fixture-to-fixture dimming performance
• Low harmonic distortion throughout entire dimming range to
maintain power quality
• Inrush current limiting circuitry to eliminate circuit breaker
tripping, switch arcing, and relay failure
Lamps
Dimming
Ballast
Control
HOT
DIMMED HOT
NEUTRAL
Hi-lume
Power
2.38”w (60mm) x 1.50”h (38mm) x 9.50”l (241mm)
• Lamps turn on at any dimmed level without flashing to full
light to eliminate nuisance flashing
• Miswire protection to eliminate potential failures caused by
improper installation
• Ultra quiet operation
• 100% performance tested prior to shipment
• 3-Year warranty
• Optional field service commissioning available – extends
warranty to 5 years (limited)
• Designed and assembled in the USA.
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-1b 1.10.02
PERFORMANCE
• Dimming range: 100% - 1%
• Ballast factor greater than .85
• Total harmonic distortion less than 10%
• Power factor greater than .95
• Lamp current crest factor less than 1.7
• No visible lamp flicker
• Class A sound rating
• Continuous ballast case operating temperature 75°C
• Minimum lamp starting temperature 10°C
STANDARDS
• UL listed, CSA approved, Class P thermally protected
• Meets ANSI C82.11 High Frequency Ballast Standard
• Meets FCC EMI/RFI emission requirements for commercial
applications
• Meets ANSI C62.41 Category A surge protection standards
• ISO 9001 Certified
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
HI-LUME 1% ARCHITECTURAL DIMMING BALLASTS
WATTS/ LAMPS PER BALLAST HI-LUME
LAMPS LENGTH BALLAST CURRENT
1
MODEL NUMBER
T8 LINEAR AND U-TUBE 18W/600mm 1 .10A FCE-0626-240-1
2 .21A FCE-0626-240-2
36W/1200mm 1 .20A FCE-1226-240-1
2 .36A FCE-1226-240-2
58W/1500mm 1 .25A FCE-1526-240-1
2 .44A FCE-1526-240-2
26mm
HI-LUME COMPACT 5% HIGH PERFORMANCE DIMMING BALLASTS
WATTS/ LAMPS PER BALLAST HI-LUME
LAMPS LENGTH BALLAST CURRENT
1
MODEL NUMBER
T4 4-PIN QUAD TUBE 26W/130mm 1 .13A FCE-CF26-240-1
2 .23A FCE-CF26-240-2
18W/110mm 1 .11A FCE-CF18-240-1
2 .18A FCE-CF18-240-2
T5 TWIN TUBE 36W/400mm 1 .18A FCE-CFL36-240-1
2 .32A FCE-CFL36-240-2
1/2" diameter
1
For maximum number of ballasts
per control, divide the control’s
current capacity by the individual
ballast current.
1
For maximum number of ballasts
per control, divide the control’s
current capacity by the individual
ballast current.
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-2b 1.10.02
5/8" diameter
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-3b 1.10.02
9.50"
(241mm)
8.91"
C-C (226mm)
2.38"
(60mm)
1.50"
(38mm)
1.70"
(43mm)
HI-LUME
® MODELS
Lamp wires
36 inches (1m).
Control wires
18 inches (.5m).
Note: For T5-HO, T8 and T12 linear lamps, maximum lamp to
ballast wire length is 7 feet (2m). For T4 Compact and T5 Twin
Tube lamps, maximum lamp to ballast wire length is 3 feet (1m).
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-4b 1.10.02
BALLAST WIRING
Note: Wire colors shown are for Lutron controls and ballasts only.
One Lamp
Two Lamps
Black (Switched Hot)*
Orange (Dimmed Hot)*
White (Neutral)
Red
Red
Blue
Blue
Fluorescent Lamp
To
Dimming
Control
Ground
Black (Switched Hot)*
Orange (Dimmed Hot)*
White (Neutral)
Red
Yellow
Yellow
Yellow
Yellow
Blue
Blue
Fluorescent Lamp
Fluorescent Lamp
To
Dimming
Control
Ground
Hi-Lume Dimming Ballast
Hi-Lume Dimming Ballast
Mount to grounded fixture
Mount to grounded fixture
* Control wire colors do not necessarily match ballast wire colors
(e.g. control “dimmed hot” may be yellow and ballast “dimmed
hot” may be orange.
Note: For T5-HO, T8 and T12 linear lamps, maximum lamp to
ballast wire length is 7 feet (2m). For T4 Compact and T5 Twin
Tube lamps, maximum lamp to ballast wire length is 3 feet (1m).
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-5b 1.10.02
ATTENTION SPECIFIERS:
APPLICATION NOTES
Perceived vs. Actual Light
An important aspect of lighting control is the difference between
measured and perceived light levels. For example, a light
dimmed
to 10% output is perceived by the eye as 32%. A light dimmed to
1% is perceived as 10%
. This “Square Law” phenomenon takes
advantage of how the human eye functions to achieve significant
energy savings, while improving the visual environment.
SPECIFICATIONS
Rapid-Start Sockets Must Be Used
Rapid-start type sockets must be used to provide proper lamp
filament heating and dimming operation.
Quality knife-edge sockets are recommended for new and
retrofit applications to ensure positive lamp/pin contact.
Mixing Ballast and Lamps per Circuit
For optimal dimming performance, do not mix ballast lamp types
(T4, T5, T8, or T12) on a given circuit. Mixing lamp lengths
(48”, 36”, 24” etc.) within a single lamp type is permissible and
will not diminish dimming performance.
Do not mix ballast types on a given circuit (i.e., mix Hi-lume with
Eco-10 or Tu-Wire).
Number of Ballasts per Control
For maximum number of ballasts per control, divide control’s
current capacity by the individual ballast current. Certain
controls also have specified number of ballast maximums.
0
20
10
1
40
60
80
100%
20
10
10
32 40 60 80 100%
LIGHT - PERCEIVED
LIGHT - MEASURED
100%
75
50
25
21
0
02510
% Light
Power (Watts)
50 75 100%
Power vs. Light
The nearly linear relationship between fluorescent light levels
and power consumption saves energy proportionately as lights
are dimmed.
®
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
JOB NAME:
JOB NUMBER:
1% ARCHITECTURAL AND 5% HIGH PERFORMANCE
ELECTRONIC FLUORESCENT DIMMING BALLASTS
220/240 Volt , T-8 Linear
T-4 Quad Tube and
T-5 Twin Tube LampsIncludes Hi-Lume Compact
Hi-lume®
rev hi-220-240-6b 1.10.02
ATTENTION CONTRACTORS
AND ELECTRICIANS:
INSTALLATION
Ballast/Socket Leads
Lead lengths from electronic dimming ballast to socket must not
exceed 7’ (2m) for T8 linear lamps.
Lamp Mounting
Many fluorescent lamp sockets are available with mounting slots
to vary the height of the lamp away from the grounded metal
surface. Use these slots to get the outside edge of the lamp to
be 1/2"+/-1/4" away from the grounded metal surface.
Having a fluorescent lamp too close to the grounded metal will
make the minimum intensity too low and will reduce lamp life.
Having a fluorescent lamp too far away from the grounded
metal will make the lamp flicker or not turn on at all.
Wiring and Grounding
All wiring from the dimming control to the Hi-lume® Ballasts is
Class 1 and may be run together in the same conduit.
Ballast and lighting fixture must have a positive electrical
contact with ground.
Ballasts must be installed per national and local electrical codes.
ATTENTION FACILITIES MANAGER:
PERFORMANCE
Lamps Must Be Seasoned
New Lamps must be operated (“seasoned”) for 100 hours at
full light output prior to dimming to achieve proper dimming
performance and ensure average rated lamp life.
Ballast Operating Temperature
Ballast case temperature must not exceed 75°C at any point on
ballast.
SERVICE
Replacement Parts
Use replacement parts with exact Lutron model numbers.
Consult Lutron if you have any questions.
Further Information
Ballasts for other lamp types and voltages may be available;
consult Lutron for further information.
For further information on dimming ballast applications, consult
Lutron’s Ballast Fluorescent Dimming Systems Guide (publication
366-606).
Download
Save PDF to desktop
Email
Email completed PDF
Send for Signing
Email for others to sign
Print
Print document
Choose a Field
Click on a field and
select the person that should complete it
Want to add a signature?
You can add a signature field
and assign it to someone else
to sign
Choose a Field
Click on a field and
select the person that should complete it

Hi 220 240 (Lutron Electronics, Inc.)

This document is locked as it has been sent for signing.

You have successfully completed this document.

Other parties need to complete fields in the document. You will recieve an email notification when the document has been completed by all parties.

This document has been signed by all parties.

Completed 18 July 2020

Message

View Audit Log
Print With Audit Log
Duplicate Document