R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hhpj-1 05.07.04
Programming Tools
Hand-Held Programmer Jack
GRAFIK Systems
NTOMX-HHPJ-__-_
Hand-Held Programmer Jack
Description
• Connects the GR6HHP Hand-Held Programmer to
GRAFIK 5000/6000/7000 Systems.
• The jack sits on a Control Station Device Link that
connects to the Processor Panel.
• The Hand-Held Programmer plugs into the jack.
• Place Hand-Held Programmer Jacks near
Wallstations, so you can plug in the Hand-Held
Programmer to adjust scenes and zones “on
location.”
Specifications
Power
Low-voltage Class 2 (PELV)
Operating Voltage: 32 VDC.
Key Design Features
• Meets IEC 801-2. Tested to withstand 15kV
electrostatic discharge without damage or memory
loss.
• Faceplate snaps on with no visible means of
attachment.
System Communications and Capacity
• Low-voltage Class 2 (PELV) wiring connects jack to
Processor Panel.
• Jacks have no address and do not count as one of
the 32 Wallstations, Control Units, or Control
Interfaces allowed on a Control Station Device Link.
Terminals
Accept up to two #18 AWG (1.0mm
2
).
Environment
32 - 104°F (0 - 40°C). 90% non-condensing relative
humidity.
Standard engraving
Color and Finish Codes
1
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hhpj-2 05.07.04
Programming Tools
Hand-Held Programmer Jack
GRAFIK Systems
Front View
Mounting
Side View
Matte Finishes
White WH
Ivory IV
Beige BE
Gray GR
Brown BR
Black BL
Metal Finishes
Bright Brass BB
Bright Chrome BC
Bright Nickel BN
Satin Brass SB
Satin Chrome SC
Satin Nickel SN
Antique Brass QB
Antique Bronze QZ
Anodized Aluminum Finishes
Clear CLA
Black BLA
Brass BRA
Also available:
-Custom Controls
-Color Matching
-Engraving
Ship in 4 to 6 weeks. Pricing
may vary depending on finishes.
Color and Finish Codes
Dimensions
2 3/4"
(70mm)
6/16"
(9mm)
1 1/8"
(29mm)
4 9/16"
(116mm)
1-Gang
U.S. Wallbox
Class 2 (PELV) Wiring
Faceplate
2
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hhpj-3 05.07.04
Programming Tools
Hand-Held Programmer Jack
GRAFIK Systems
• Daisy-chain the Hand-Held Programmer Jack onto the
low-voltage Class 2 (PELV) Control Station Device Link.
• Make all connections in the Programer Jack’s wallbox
or in a switchbox or junction box with a maximum wire
length of 8 ft. (2.5m) from the link to the jack.
• Consult the Processor Panel Specification Submittal
for more details.
• Two #12 AWG (2.5mm
2
) conductors for Common and
32VDC.
• One shielded, twisted pair #18 AWG (1.0mm
2
) for data
link (terminals 3 and 4).
• Connect Drain/Shield as shown in Wallstation Wiring.
Do not connect to Ground (Earth) or jack. Connect the
bare drain wires and cut off the outside shield.
The Jack connects the Hand-Held Programmer to the System.
Processor Panel
Control
Interface
Control Unit
Class 2 (PELV) Control Station Device Link
GR6HHP
Hand-Held
Programmer
Programmer
Jack
Programmer
Jack
Low Voltage Class 2 (PELV) Wiring
Jack Wire
Black (or White)
Red
Yellow
Blue
Class 2 (PELV)
Terminal Connection
1: Common
2: 32VDC
3: MUX
4: MUX
3