Fillable Hp246 HP 2 4 6.qxp (Lutron Electronics, Inc.)

Fill Online, Printable, Fillable, Blank Hp246 HP 2 4 6.qxp (Lutron Electronics, Inc.) Form

Use Fill to complete blank online LUTRON ELECTRONICS, INC. pdf forms for free. Once completed you can sign your fillable form or send for signing. All forms are printable and downloadable.

Hp246 HP 2 4 6.qxp (Lutron Electronics, Inc.)

On average this form takes 12 minutes to complete

The Hp246 HP 2 4 6.qxp (Lutron Electronics, Inc.) form is 7 pages long and contains:

  • 0 signatures
  • 0 check-boxes
  • 49 other fields

Country of origin: US
File type: PDF

Use our library of forms to quickly fill and sign your Lutron Electronics, Inc. forms online.

BROWSE LUTRON ELECTRONICS, INC. FORMS

Related forms
Fill has a huge library of thousands of forms all set up to be filled in easily and signed.
Fill in your chosen form
Sign the form using our drawing tool
Send to someone else to fill in and sign.
find another form
 
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-1 04.05.04
Power Equipment
HP 2-4-6
®
Hi-Power Dimming Module System
Description
• Used to dim or switch heavily loaded
zones. Allows a wall dimmer or one
zone on a GRAFIK Eye 3000 Series
Control Unit to control loads of up to
30,000W/VA.
• Dims or switches most popular lighting
sources and load types.
• Available in one, two, and three-circuit
Dimming Modules. Up to five Modules
may be linked to obtain the necessary
load capacity.
• Accepts either 120V or 277V input
power. Not compatible with 220-240V,
230V, or 100V input power.
• Control using GRAFIK Eye 3000 Series
Control Units, Lutron Wallbox Controls,
Spacer System, or any incandescent
dimmer or Class 2 momentary contact
raise/lower control.
• Allows control of 277V loads using a
120V lighting control.
Typical Three-Circuit Dimming Module
120V Distribution
Panel
Feed (input) circuits
“feed through” to …
… load (output) circuits.
HP-6
Dimming Module
• Control Circuit Wiring
• Dimmed Hot from Zone
GRAFIK Eye 3000
Series Control Unit
Lighting Load
Lighting Load
Lighting Load
1
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-2 04.05.04
Power Equipment
HP 2-4-6
®
Power
• Input power: 120V or 277V, 50/60Hz, phase-to-neutral.
• Load (output) circuits: 120V or 277V, 50/60Hz, any
phase.
Adjustable Settings
• High-end trim reduces expensive relamping of
incandescent/halogen sources.
• Provides raise/lower and “full on” functions when used
with external momentary contact switches.
• Provides adjustable fade rate when used with Class 2
raise/lower control.
Weight
15 lbs. (6.8kg)
Mounting
Surface mount indoors only. Allow space for ventilating
200 BTUs/hour per load (output) circuit.
Environment
32-104°F (0-40°C). Non-condensing relative humidity less
than 90%.
Specifications
2
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-3 04.05.04
Power Equipment
HP 2-4-6
®
• All Dimming Modules accept either 120V or 277V input
power. Do not mix voltages in the same Module.
• Each load circuit on HP-4 and HP-6 Dimming Modules
can have different sources. Do not mix sources on the
same load circuit.
• Up to five Modules may be linked to obtain the
necessary load capacity.
• Do not use the HP Dimming Module with Capacitive
Fluorescent Ballasts.
Model
Number
HP-2
HP-4
HP-6
Number of
Circuits
1
2
3
Source
Incandescent
Electronic Low Voltage
2
Magnetic Low Voltage
Fluorescent (Hi-Lume/Compact SE/Eco-10)
Fluorescent (Tu-Wire)
Fluorescent (magnetic ballasts)
Fluorescent (electronic ballasts)
Neon/Cold Cathode
High-Intensity Discharge
Load Capacity per Circuit - Dimmed or Switched
(Not to exceed N.E.C. capacity rating; control voltage is always 120V)
Dimmed (120V)
16A, 2000W/VA
1
16A, 2000W/VA
1
16A, 2000W/VA
1
16A, 2000W/VA
1
16A, 2000W/VA
1
-
-
16A, 2000W/VA
1
-
Switched (120V)
10A, 1200W/VA
10A, 1200W/VA
10A, 1200W/VA
16A, 1920W/VA
16A, 1920W/VA
16A
10A
10A, 1200W/VA
10A, 1200W/VA
Dimmed (277V)
-
-
16A, 4432W/VA
16A, 4432W/VA
-
-
-
-
-
Switched (277V)
-
-
-
-
-
-
-
-
-
Models, Sources, and Capacities
2
Requires electronic low voltage transformer approved for use with forward phase control dimmers.
1
Measured current will not exceed continuous load rating due to voltage drop in the dimmer.
3
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-4 04.05.04
Power Equipment
HP 2-4-6
®
Dimensions
• Surface mount indoors.
• Dimming Module generates heat; mount
only where ambient temperature is 32-
104°F (0-40°C).
• Provide proper space for cooling or the
warranty will be void. Leave 6" (152mm) of
clearance in front of the Module. Do not
block the air channel between the back of
the Module and the wall. The space
between panels may be reduced to 4.5"
(114mm) when mounting several Modules
in a vertical layout.
• Mount Modules where audible noise is
acceptable. (Modules hum slightly and
relays click.)
• Mount Modules so line (mains) voltage
wiring is at least 6 feet (1.8m) from sound
or electronic equipment and wiring.
• Mount Modules within 7° of true vertical.
Bottom View
9 1/4"
(235mm)
14 1/2"
(368mm)
9 3/8"
(238mm)
10 3/8"
(264mm)
2"
(51mm)
2 3/16"
(56mm)
Right Side ViewFront View
6"
(152 mm)
3"
(76mm)
5 7/8"
(150mm)
2 7/8"
(73mm)
2 3/8"
(60mm)
4 1/8"
(104mm)
Low-voltage type
Class 2 (PELV)
wiring must
enter here
Mounting
Module
HP-2
HP-4
HP-6
Maximum
BTUs/Hour
200
400
600
Weight
(Without Packaging)
11 lbs. (5.0kg)
13 lbs. (5.9kg)
15 lbs. (6.8kg)
3"
(76mm)
Air Channel
6"
(152 mm)
3"
(76mm)
10"
(253mm)
4
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-5 04.05.04
Power Equipment
HP 2-4-6
®
• Each terminal accepts two #12 AWG (2.5mm
2
) wires.
• Each load circuit on HP-4 and HP-6 Dimming Modules
can have different sources. Do not mix sources on the
same load circuit.
• Do not use with generator-supplied power.
CLASS 2
4
3
2
1
NEUTRAL
SSA
ZONE 3
ZONE 2
ZONE 1
HOT/LIVE
CU WIRE ONLY
USA: Class 2
IEC: PELV
Load circuit terminals have factory-installed bypass
jumper(s) between the H (Hot), SH (Switched Hot),
and DH (Dimmed Hot) terminals of each load circuit.
Do not remove jumpers until installation is complete
and load circuit is cleared of miswires/overloads.
Feed Wiring
• Pull dedicated feeds from distribution panel to Dimming
Module(s): one feed for HP-2, two feeds for HP-4, three
feeds for HP-6.
• Run separate neutrals for each feed - no common neutrals.
Prewiring Overview
Load Circuits
• (2) #12AWG Typical
• (3) #12AWG (2.5mm
2
) for
dimmed fluorescent
To additional Dimming
Modules (if used)
(3) #12AWG (2.5mm
2
)
Rear View of GRAFIK Eye Control Unit
Lighting Load
HP-6
Dimming Module
Dimmed Hot
Control Circuit Wiring
(3) #12AWG (2.5mm
2
)
Feeds
(2) #12AWG (2.5mm
2
) Typical
120V
Distribution Panel
120V or 277V
Distribution Panel
Lighting Load
Lighting Load
5
N N H H DH 1 2 3
CLASS 2
4
3
2
1
NEUTRAL
SSA
ZONE 3
ZONE 2
ZONE 1
HOT/LIVE
CU WIRE ONLY
USA: Class 2
IEC: PELV
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-6 04.05.04
Power Equipment
HP 2-4-6
®
GRAFIK Eye Control Unit Wiring
Module-to-Module Wiring
• Pull three #12AWG (2.5mm
2
) wires between the Dimming
Modules to be used on a zone.
• Modules must be daisy-chained.
• Connect the GRAFIK Eye Control Unit to the first Dimming
Module used in the zone.
• Use two #12AWG (2.5mm
2
) wires to connect the Control Unit’s
feed to the Dimming Module’s control circuit. This allows
Dimming Modules to draw 40W/VA power for internal operations.
• Use one #12AWG (2.5mm
2
) wire to carry the zone’s dimmed (or
switched) hot signal from the Control Unit to the Dimming
Module. This allows the Control Unit to control the lighting loads.
• Make sure the power for the control circuit is 120V and on the
same phase as the GRAFIK Eye Control Unit.
• Make sure the Control Unit’s feed can support all the Dimming
Modules drawing off it. Each HP 2-4-6 Dimming Module draws
approximately 0.1A of current.
• Use a separate raceway. Do not mix control circuit wiring with
feed or load wiring.
Dimmed Hot
Hot/Live
Neutral
Neutral
Hot/Live
Rear View of GRX-3103 Control Unit
To additional
loads
Control Circuit Feed
(3) #12 AWG
(2.5 mm
2
)
120VAC
Feed from
Distribution
Panel
HP 2-4-6
(3) #12 AWG (2.5 mm
2
)
To additional
HP 2•4•6
Modules
(Five maximum)
Control
Circuit
Terminals
6
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
hp246-7 04.05.04
Power Equipment
HP 2-4-6
®
N1 H1 DH1 SH1
N1 H1 DH1 SH1
120V Switched Load Circuits
Hi-lume® and Eco-10TM (Eco Series) Fluorescent Dimming Ballasts
N1 H1 DH1 SH1
120V or 277V Dimmed Load Circuits
All load types except Lutron Hi-lume
®
or Eco-10
TM (Eco
Series) Fluorescent Dimming Ballasts. Circuit 1 shown.
Typical Load Circuits
Neutral
Feed for Load Circuit 1
120V or 277V
Dimmed Hot
Neutral
Load
Hot/Live
Feed-Through Load
Circuit Terminal
HP-2
Load
Neutral
Switched Hot
HP-2
Feed-Through Load
Circuit Terminal
Neutral
Hot/Live
Feed for Load Circuit 1
120V only
HP-2
Feed-Through Load
Circuit Terminal
Neutral Hot/Live
Feed for Load Circuit 1
120V or 277V
Hi-Lume (FDB) or
Eco-10 (ECO)
Dimming Ballast
To additional
Dimming Ballasts
White (Neutral)
Orange (Dimmed Hot)
Ground
Black (Switched Hot)
7
Download
Save PDF to desktop
Email
Email completed PDF
Send for Signing
Email for others to sign
Print
Print document
Choose a Field
Click on a field and
select the person that should complete it
Want to add a signature?
You can add a signature field
and assign it to someone else
to sign
Choose a Field
Click on a field and
select the person that should complete it

Hp246 HP 2 4 6.qxp (Lutron Electronics, Inc.)

This document is locked as it has been sent for signing.

You have successfully completed this document.

Other parties need to complete fields in the document. You will recieve an email notification when the document has been completed by all parties.

This document has been signed by all parties.

Completed 18 July 2020

Message

View Audit Log
Print With Audit Log
Duplicate Document