Fill - Free fillable 3691104 POWPAK 1-ZONE DALI SPEC (3691104) PDF form

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 1 09.24.19

PowPak Single Zone Control Module

with DALI

The PowPak Single Zone Control Module with DALI® is a

radio frequency (RF) control that operates 1–4 or 1–32*DALI®

LED drivers or fluorescent ballasts based on input from Pico

remote controls and RadioPowr Savr sensors. The control

module is ideal for small areas (e.g.,classrooms, conference

rooms, private offices).

Communication with RF input devices (e.g., Pico remote

controls, Radio Powr Savr sensors) is accomplished by using

Lutron Clear Connect RF technology.

These products are also compatible with the Vive hub which

enables a simple setup process using the free Lutron Vive

app (available for download from the App Store or Google

PlayR online marketplace) or by using web-based software

with any Wi-FiR enabled iOSR or AndroidR compatible device.

It also enables control and monitoring of all Vive devices. The

Vive hub can be added at any time. System reprogramming

will be required. For a complete list of features supported with

the Vive hub, see specification submittal 3691044 at

www.lutron.com

Features

• Controls 1–4 or 1–32DALI® fixtures in a single zone

(see Models see below).

• Configurable high- and low-end trim.

• Receives wireless inputs from up to 10 Pico remote controls,

10 Radio Powr Savr occupancy / vacancy sensors, and 1

Radio Powr Savr daylight sensor.

• Utilizes Lutron Clear Connect RF technology; refer to model

number chart below for frequency band data.

• Mounts through a 20 mm knockout.

DALI® Compatibility

The Lutron PowPak Single Zone Control Module with DALI® is DALI-2® certified by the Digital Illumination Interface Alliance

(DiiA)®. In order to ensure compatibility with Lutron DALI® controllers, the connected DALI® LED drivers and fluorescent

ballasts must be DALI-2® certified and marked. In addition to compatibility, it is important to select high-quality and

high-performance LED drivers and fluorescent ballasts. DALI-2® certified devices are readily available from many

manufacturers and are tested for compatibility with the standard. For a complete list of available DALI-2® certified devices,

see the DiiA® website at https://www.digitalilluminationinterface.org/products. DALI® devices that are not listed on the DiiA®

website and are not marked DALI-2® cannot be considered DALI-2® certified.

The DALI® version-1 standard does not ensure compatibility. To apply the original DALI® version-1 mark on LED drivers and

fluorescent ballasts, no verification of the test results was required, and manufacturers could self-declare compliance and

apply the DALI® mark. If you would like to use an LED driver or fluorescent ballast that is not DALI-2® certified but carries a

DALI® version-1 logo, Lutron recommends that these devices be tested to ensure compatibility. Lutron is able to perform

this testing on request. Samples of the drivers and light engines must be submitted to Lutron and the expected turnaround

time is 6 to 8 weeks after the drivers are received. Fees for testing may apply. Lutron recommends that this testing be

performed before the fixtures and lighting controls are purchased and installed. Contact your Lutron sales representative

for more information.

Note: Contact Lutron for frequency band compatibility for your geographic region if it is not indicated above.

* See Models listed in chart.

Models

Model Number Description Region Operating Voltage Frequency Band

RMKS-DAL32-SZ 32 device controller U.K., Europe 220 –240 V~ 868.125 – 869.850 MHz

RMKS-DAL4-SZ 4 device controller U.K., Europe 220 –240 V~ 868.125 – 869.850 MHz

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 2 09.24.19

Specifications

Regulatory Approvals

• CE

• IEC 60669-2-5

• DALI-2

® Certified

Power

• 220 –240V~ 50 / 60Hz, max. current 50 mA

Other Power Specifications

• Standby power:

220–240 V~ <0.5 W

System Communication

• Operates using Clear Connect RF technology for

reliable wireless communication.

• Wireless sensors and controls must be located within

9m of the associated control module.

Mounting*

• This device can be installed on a fixture / troffer,

junction box, or marshalling box using the conduit

nut or with mounting screws. The device must NOT

be mounted inside a fixture / troffer or other metallic

enclosure.

• Refer to the installation instructions and consult local

and national electric codes for proper installation.

• The PowPak Control Module needs to be accessible

for some programming steps. Record where it is

mounted so that it can be easily located later.

Metal Ceiling Mounting

• Metal ceiling grids must have a > 3 mm gap of non-

metal material which extends the entire length of

the tile on at least one edge. This is often achieved

by foam spacers that are used to prevent tile-to-tile

rattling.

• Metal ceiling grids which are continuous (with no

gap) or those that are interlocked, must have a total

surface area that is less than 81m

for each section.

The overall space can be larger as long as there are

non-metal sections bordering or intersecting the

metal sections.

Environment

• Ambient operating temperature: 0°C to 40°C

• 0% to 90% humidity, non-condensing.

• For indoor use only.

• All drivers and ballasts used with Vive wireless

controls must comply with EN 55015 / CISPR 15.

Key Design Features

• LED status indicator shows load status and provides

programming feedback.

• Configurable high-end and low-end trim.

• Power failure memory: If power is interrupted,

connected loads will return to the previous level prior

to interruption.

Continued on next page...

* For more guidelines and installation best practices, refer to Lutron Application Note

#620 (P/N 048620) at www.lutron.com

NOTICE: Improper installation can result in

degraded wireless communication and/or

intermittent or sustained communication failures,

and will not be covered under warranty.

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 3 09.24.19

Specifications (continued)

DALI® Link

• 18 V-

• Controls 1–4 or 1–32 DALI

® ballasts or drivers (see

Models on page 1)

– Multiple drivers / ballasts connected to a Control

Module will always work together as a single zone.

• Guaranteed Supply Current

– 8 mA (RMKS-DAL4-SZ)

– 64 mA (RMKS-DAL32-SZ)

• Maximum Supply Current: 250 mA

• DALI

® Digital Link carries basic isolation from line

voltage wires.

• The PowPak Control Module is a single master

controller and therefore no other controllers may exist

on the same DALI

® bus.

• Ensure that there is no greater than a 2 V~ drop

between the Control Module and the end of the

DALI

® Bus.

• Consult all national and local electrical codes for

separation requirements.

Wire Gauge Total DALI®-compliant Bus

Wire Length

1.5 mm

(14 AWG) 300 m

0.75 mm

(18 AWG) 150 m

0.50 mm

(20 AWG) 100 m

Default Operation

• Associated wireless input devices control all

connected fixtures together.

• Occupancy Sensors:

– Occupied:100%; Unoccupied:0% (OFF)

• Pico Remote Controls:

– On:100%; Favorite Level:50%; Off:0% (OFF)

• Daylight Sensor: Decreases electric light in response

to additional available daylight

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 4 09.24.19

Advanced Configurations

Pico Remote Controls

• Up to 10 Pico remote controls.

• Favorite levels can be set for each Pico remote control.

Radio Powr Savr Daylight Sensor

• The Radio Powr Savr daylight sensor will affect all

connected LED drivers and ballasts equally.

• For multiple rows of daylighting, a separate PowPak

Control Module must be used for each daylighting

row.

Minimum Light Level Setting (optional)

• Certain applications, such as hallways, may require

that the lights never turn off. For these areas, select

the minimum light level option and the load will lower

to programed low-end level. Default operation lowers

to OFF.

High- and Low-End Trim

• High-end and low-end trim affect all connected fixtures

equally, and can be configured from the PowPak

Control Module.

• Adjustable low-end trim (0.1% –45%)*. Trimmable

low-end can ensure a stable light level. Some fixtures

will flicker or drop out if trimmed too low.

• The maximum light output of connected fixtures can

be decreased down to 55% for energy savings in over-

lit spaces.

Note: The perceived light output of low-end trim may

vary between fixture manufacturers and model

numbers. For best results, do not mix different drivers

or ballasts on the same DALI

® circuit.

Radio Powr Savr Occupancy Sensors

• Radio Powr Savr occupancy and vacancy sensors

control all connected drivers or ballasts.

• Pico remote controls can be used to adjust the

occupied levels of fixtures that they control from

0.1%* to 100% (of output signal) or can make them

unaffected by occupancy events.

• Vacancy events (area becomes unoccupied) turn all

driver or ballast models off or to minimum light level.

* Low-end depends on the minimum output of the connected

drivers or ballasts.

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 5 09.24.19

System Diagram

Wiring Schematic

Radio Powr Savr occupancy sensor (up to 10)

Radio Powr Savr daylight sensor (up to 1)

Pico remote control (up to 10)

LED Drivers Fluorescent Ballasts

DALI

® control

* Can be installed in a junction box or marshalling box. Please follow all local and

national electric codes for proper installation methods.

Line / Hot

Junction Box*

Neutral

DA+

DA−

DALI® to LED Drivers / Fluorescent Ballasts

20 mm knockout opening

Adaptor

Note: Multiple drivers / ballasts connected to a PowPak

Control Module will always work together as a single zone.

Note: The perceived light output of low-end trim may vary

between fixture manufacturers and model numbers. For

best results, do not mix different drivers or ballasts on the

same DALI

® circuit.

To additional fixtures

(up to 4 or up to

32DALI® ballasts or

drivers – see Models on

page1)

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive

PowPak Single Zone Control Module with DALI® Wireless Lighting Control

3691104c 6 09.24.19

Dimensions

Dimensions are shown as: mm

100

Wireless Range Diagram

9 m

maximum

Radio Powr Savr

occupancy

sensor

Pico

remote

control

PowPak

Control Module

Install in center of room

to maximize RF coverage.

PowPak

Control

Module

Lutron, )Lutron, PowPak, Radio Powr Savr, Clear Connect, Vive, and Pico

are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the

US and/or other countries.

All other product names, logos, and brands are property of their respective

owners.

App Store is a service mark of Apple Inc.

Note: Wireless sensors and controls must be located within

9m of the associated control module.

• Metal ceiling grids must have a > 3mm gap of non-metal

material which extends the entire length of the tile on at least

one edge. This is often achieved by foam spacers that are

used to prevent tile-to-tile rattling.

• Metal ceiling grids which are continuous (with no gap) or

those that are interlocked, must have a total surface area that

is less than 81 m

for each section. The overall space can be

larger as long as there are non-metal sections bordering or

intersecting the metal sections.

20 mm knockout opening

112

Adaptor

Download
Save PDF to desktop

Email
Email completed PDF

Send for Signing
Email for others to sign

Print
Print document

NAME

3691104 POWPAK 1-ZONE DALI SPEC (3691104)

View Audit Log
Print With Audit Log
Duplicate Document

Fill Online, Printable, Fillable, Blank 3691104 POWPAK 1-ZONE DALI SPEC (3691104) Form

Related forms

Fillable 3691104 POWPAK 1-ZONE DALI SPEC (3691104)

Fill Online, Printable, Fillable, Blank 3691104 POWPAK 1-ZONE DALI SPEC (3691104) Form

Related forms

First 20 documents completely FREE!