T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 1 12.17.19
T-Series LED Drivers provide a high-performance
tunable white solution.
Features
• ULR 8750 Listed Class P
Each output capable of 100% to 0.1% dimming *
For best tunable white performance, operate at 1% or
higher. See page 10 for more details
Dimming Method:
Constant-current reduction (CCR) dimming to
200 mA
Pulse-width modulation (PWM) dimming below
200 mA
e
PWM Frequency = 3.6 kHz
e
Outputs of the two channels are synchronized
Driver consumes two digital addresses: one for
intensity and one for color temperature
Guaranteed performance and compatibility when
used with Lutron T-Series controls:
T-Series Energi Savr Node unit as part of a
Quantum system
Guaranteed compatibility with T-Series Energi Savr
Node as a part of a Quantum system
QwikFig Air compatible
Protected from miswires of input power to T-Series
control inputs up to 277 V~
Rated lifetime of 50,000 hours at 167 °F (75 °C)
calibration point (t
c
) for W case and 158 °F (70 °C)
calibration point (t
c
) for Y case
FCC Part 15 Class A
100% performance tested at factory before shipping.
RoHS compliant
For more information please visit: www.lutron.com
T-Series LED Driver
Case Type W
1.18 in (30 mm) W x 0.83 in (21.0 mm) H x 16.06 in (408 mm) L
Case Type YS
3.0 in (76.0 mm) W x 1.14 in (29.0 mm) H x 5.91 in (150.0 mm) L
Case Type YN
3.0 in (76.0 mm) W x 1.14 in (29.0 mm) H x 5.91 in (150.0 mm) L
T-Series Digital Link Features
Simpler to wire and more reliable than 0 10 V-
Guarantees compatibility between Lutron controls
and LED drivers
Accommodates zone and control changes
without rewiring
Connect to Quantum Total Light Management
Systems to monitor lighting power consumption
Polarity-free and topology-free
Allows easy code compliance
T-Series digital link can be Class 1 or Class 2
Non-volatile memory restores all settings after
power failure
* Light output at low-end depends on the efficacy of the LED light engine used with the driver.
CLASS P
E322469
t
c
N
L
Suitable for damp locations. Indoor Use Only.
Convient aux emplacements humides. Usage intérieur
seulement.
Class B | Classe B | Clase B
To remove wire, insert screwdriver into slot.
Pour enlever le fil, insérez un tourneviz dans la fente.
Para retirar el cable, insertar destornillador en la ranura.
Assembled in China | Assemblé en Chine | Ensamblado en China
Warranty void if unit opened. | Garantie annulée si ouvert.
La garantia sera nula si se abre la unidad.
T-Series
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
lutron.com
B3
En México: Importado Por: Lutron CN. S. De R.L. De C.V.
Gabriel Mancera 1041 Colonia Del Valle, México DF. 03100 México
Cu
Al
0,35 in.
(9 mm)
Wire: Solid,
20-16 AWG, 90 ˚C
Alambre: Sólido,
20-16 AWG, 90 ˚C
Fil: Solide,
20-16 AWG, 90 ˚C
PCB
Adecuado para lugares humedos. Solamente para uso
en interiores.
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría ocasionar lesiones
graves o la muerte. Hay presente más de una fuente de alimentación;
desconecte la alimentación eléctrica antes de brindar mantenimiento o
instalar.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present, disconnect power before
servicing or installing.
T-Series LED Driver
PSQ02UWN-5ABLK
120 - 277 V~
CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
66 W
0 784276 180344
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Class 2
LED
Driver
C2-
C2+
N
L
C1-
C1+
T2
T1
T1
T2
LED Driver | Pilote de LED | Controlador LED
N/C
T2
T1
N/C
T2
T1
N/C
N/C
C2
-
C2
+
Cool
C1-
C1
+
Warm
Clase P
For rated warranty tc 75 ˚C max. | Pour garantie nominale tc 75 ˚C max. |
Para la garantia nominal tc 75 ˚C max.
For rated warranty tc 70 ˚C max. | Pour garantie nominale tc 70 ˚C max. |
Para la garantia nominal tc 70 ˚C max.
lutron.com
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
ADVERTENCIA: Peligro de descarga eléctrica. Podría
ocasionar lesiones graves o la muerte. Hay presente más
de una fuente de alimentación; desconecte la alimentación
eléctrica antes de brindar mantenimiento o instalar.
l'alimentation avant d'effectuer l'entretien ou l'installation.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present,
disconnect power
before servicing or installing.
Assembled | Ensamblado | Assemble: China | Chine
C2+
C2-
C1+
C1-
N/C
N/C
N/C
N/C
T1
T2
N/C
T1
T2
N/C
L
N
t
c
T-Series
LED Driver | Pilote de LED | Controlador LED
To remove wire, insert screwdriver into slot. | Pour enlever
le fil, insérez un tourneviz dans la fente. | Para retirar el
cable, insertar destornillador en la ranura.
Cu
Al
0,35 in.
(9 mm)
Wire: Solid, 20-16 AWG, ≥ 90 ˚C
Alambre: Sólido, 20-16 AWG,
≥ 90 ˚C
Fil: Solide, 20-16 AWG, ≥ 90 ˚C
PCB
Suitable for damp locations. Indoor Use Only. | Convient aux
emplacements humides. Usage intérieur seulement. | Adecuado
para lugares humedos. Solamente para uso en interiores.
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia
sera nula si se abre la unidad.
Class B | Classe B | Clase B
Cool
Warm
Class 2
LED
Driver
C2+
C2-
T2
T1
T2
T1
C1+
C1-
N
L
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
T-Series LED Driver
PSQ02UYS-5ABLK
120 - 277 V~ CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
62 W
0 784276 180382
CLASS P
E322469
Clase P
En México: Importado Por:
Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041
Colonia Del Valle México DF. 03100 México
For rated warranty tc 70 ˚C max. | Pour garantie nominale tc 70 ˚C max. |
Para la garantia nominal tc 70 ˚C max.
lutron.com
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
ADVERTENCIA: Peligro de descarga eléctrica. Podría
ocasionar lesiones graves o la muerte. Hay presente más
de una fuente de alimentación; desconecte la alimentación
eléctrica antes de brindar mantenimiento o instalar.
l'alimentation avant d'effectuer l'entretien ou l'installation.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present,
disconnect power
before servicing or installing.
Assembled | Ensamblado | Assemble: China | Chine
C2+
C2-
C1+
C1-
N/C
N/C
N/C
N/C
T1
T2
N/C
T1
T2
N/C
L
N
t
c
To remove wire, insert screwdriver into slot. | Pour enlever
le fil, insérez un tourneviz dans la fente. | Para retirar el
cable, insertar destornillador en la ranura.
Cu
Al
0,35 in.
(9 mm)
Wire: Solid, 20-16 AWG, ≥ 90 ˚C
Alambre: Sólido, 20-16 AWG,
≥ 90 ˚C
Fil: Solide, 20-16 AWG, ≥ 90 ˚C
PCB
Suitable for damp locations. Indoor Use Only. | Convient aux
emplacements humides. Usage intérieur seulement. | Adecuado
para lugares humedos. Solamente para uso en interiores.
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia
sera nula si se abre la unidad.
Class B | Classe B | Clase B
Cool
Warm
Class 2
LED
Driver
C2+
C2-
T2
T1
T2
T1
C1+
C1-
N
L
T-Series LED Driver
PSQ02UYN-5ABLK
120 - 277 V~ CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
62 W
0 784276 180382
CLASS P
E322469
Clase P
50017898
10/15/2019
Front Label Size: 4.95” x 2.77”
Corner Radius: 0.05”
Color: Pantone Process Blue, Black
Die Line - Do not print
En México: Importado Por:
Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041
Colonia Del Valle México DF. 03100 México
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
1
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 2 12.17.19
Specifications
Regulatory Approvals and Compliance
cULus Listed Class P
NOM certified
Lutron Quality Systems registered to ISO 9001.2015
Inrush current less than NEMA 410-2011 limit
FCC Part 15 Class A
Meets UL® 8750, “Light Emitting Diode (LED)
Equipment For Use in Lighting Products”
Class 2 outputs
Compliant with perfomance criteria for ENERGY STAR
for Luminaires Version 2.1 in designated areas (see
Load Compatibility graph in Output Ranges page 6)
Compliant with DLC version 4.3 in designated areas
(see Load Compatibility graph in Output Ranges
page 6) (for W case only)
Performance
Dimming Range: 100% to 0.1%
1
Operating Voltage: 120 V~ / 277 V~ at 50 / 60 Hz
Lifetime: 50,000 hours when calibration point (t
c
) at
167 °F (75 °C) for W case and 158 °F (70 °C) for
Y case
2
• ULR allows operation of t
c
up to 90 °C
For rated warranty, t
c
not to exceed 167 °F (75 °C) for
W case and 158 °F (70 °C) for Y case (maximum rated
temperature)
2
At turn on, lighting goes to the desired level without
decreasing or flashing to full brightness
Typical standby power consumption: < 0.5 W at
120 V~ / 277 V~
Open-circuit protected output
Short-circuit protected output
Over temperature protected
Environmental
Sound rated: Class A inaudible in 24 dBA ambient
Relative Humidity: maximum 90% non-condensing
Minimum Operating Ambient Temperature:
t
a
= 0 °C (32 °F)
3
Indoor use only
Rated for dry and damp locations
OEM Notes
For best dimming performance, Lutron recommends
electrical insulation with 50 / 60 Hz impedance of at
least 12 MΩ and minimum breakdown voltage of at
least 1500 V~ between LEDs and fixture chassis
Driver Wiring and Mounting
Driver is grounded by a mounting screw to the
grounded fixture or by a terminal connection.
It is possible to daisy-chain the T-Series digital link
using the second set of terminal blocks. See example
on page 10
Fixture must be grounded in accordance with local
and national electrical codes
The positive terminals of both output channels are
electrically connected inside the driver. This supports
the use of common anode loads
Terminal blocks on the driver accept one solid wire per
terminal from 20 AWG to 16 AWG (0.5 mm
2
to 1.5 mm
2
)
Maximum driver-to-LED light engine wire length for:
Wire Gauge
Maximum Lead Length
150 mA to
700 mA
710 mA to
1.50 A
1.51 A to
2.10 A
18 AWG (0.75mm
2
) 30 ft (9 m) 15 ft (4.5 m) 10 ft (3 m)
16 AWG (1.5mm
2
) 35 ft (10.5 m) 25 ft (7.5 m) 15 ft (4.5 m)
14 AWG (2.5mm
2
)
4
50 ft (15 m) 40 ft (12 m) 25 ft (7.5 m)
12 AWG (4.0mm
2
)
4
100 ft (30 m) 60 ft (18 m) 40 ft (12 m)
1
For best tunable white performance, operate at 1% or higher. Light output at
low-end depends on the efcacy of the LED light engine used with the driver.
2
To maintain warranty, installer is responsible for ensuring that the driver calibration
point does not exceed 167 ºF (75 ºC) for W case and 158 ºF (70 ºC) for Y case.
3
Where t
a
is the temperature of the air directly surrounding the driver.
4
Terminal blocks on the drivers accept only solid 20 AWG to 16 AWG (0.5 mm
2
to
1.5 mm
2
) wire. To use wire gauges larger than the terminal blocks’ rated gauge of
16 AWG (1.5 mm
2
), connect up to 3 ft (1.0 m) of 20 AWG to 16AWG (0.5 mm
2
to
1.5 mm
2
) wire to the LED driver terminal blocks, then connect 12 AWG or 14 AWG
(4.0 or 2.5 mm
2
) up to the length allowed in the above table.
2
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 3 12.17.19
Output Voltage (V)
30
20
10
0
0.00
0.15
0.30 0.45
0.60
Output Current (A)
60
50
40
0.75
0.90
1.201.05
Key:
Constant 20 W output Constant 54 V output
How to Determine Compatibility Between an LED Driver and LED Load
1. Review the specifications of the LED load.
2. Identify the minimum and maximum operating voltage of the LED load at the desired operating current. This
current” will be the rated output current of the LED driver. Consult the LED load manufacturer for any questions.
Example: An LED load that is rated at 0.7A and 30V nominally, has an input (forward) voltage range of
25 35V (at 0.7A) due to unit-to-unit variation, temperature, etc.
3. Examine the LED driver Load Compatibility graphs below for each output range to ensure that the voltage range
of the LED load is within the load compatibility range.
Example: Lines* marked below indicate two load specifications:
Load A (25 – 35 V) at 0.5 A
Load B (25 – 35 V) at 0.7 A
Load B (Not Compatible)
Since the maximum voltage of the load, 35 V, exceeds the
28.5 V allowable at 0.7 A, this combination of LED load and
LED driver is not compatible.
Load A (Compatible)
Operating voltage range for load A is 25 35 V at 0.5 A. Since
the load specifications are within the operating range, the
combination of LED load and LED driver is compatible.
35 V
25 V
Operating
range of 0.5 A,
25 – 35 V load
Output Voltage (V)
30
20
10
0
0.00
0.15
0.30 0.45
0.60
Output Current (A)
60
50
40
0.75
0.90
1.201.05
Key:
Constant 20 W output Constant 54 V output
}
{
Operating range
of 0.7A,
25 – 35V load
Load Compatibility
35 V
25 V
4. The LED Driver Selection Tool (www.lutron.com/drivers) is a website compatibility tool that allows for a fast
compatibility search of all Lutron LED drivers that are compatible with an LED load.
5. See T-Series Model Number to create the appropriate model number for the desired driver. T-Series drivers are
only available as “BLK” drivers for use with QwikFig Air.
* Lines are an example and not the range of the T-Series LED driver.
3
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 4 12.17.19
T-Series Model Number
* Output voltage range changes with output current and according to power limits. Check driver specifications on the following pages carefully to
understand output voltage range of a particular SKU. Purchaser is responsible for electrical compatibility between LED driver and LED load.
P S Q 0 2 U M M M A B L K
W-case type
YS-case type
YN-case type
CLASS P
E322469
t
c
N
L
Suitable for damp locations. Indoor Use Only.
Convient aux emplacements humides. Usage intérieur
seulement.
Class B | Classe B | Clase B
To remove wire, insert screwdriver into slot.
Pour enlever le fil, insérez un tourneviz dans la fente.
Para retirar el cable, insertar destornillador en la ranura.
Assembled in China | Assemblé en Chine | Ensamblado en China
Warranty void if unit opened. | Garantie annulée si ouvert.
La garantia sera nula si se abre la unidad.
T-Series
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
lutron.com
B3
En México: Importado Por: Lutron CN. S. De R.L. De C.V.
Gabriel Mancera 1041 Colonia Del Valle, México DF. 03100 México
Cu
Al
0,35 in.
(9 mm)
Wire: Solid,
20-16 AWG, 90 ˚C
Alambre: Sólido,
20-16 AWG, 90 ˚C
Fil: Solide,
20-16 AWG, 90 ˚C
PCB
Adecuado para lugares humedos. Solamente para uso
en interiores.
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría ocasionar lesiones
graves o la muerte. Hay presente más de una fuente de alimentación;
desconecte la alimentación eléctrica antes de brindar mantenimiento o
instalar.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present, disconnect power before
servicing or installing.
T-Series LED Driver
PSQ02UWN-5ABLK
120 - 277 V~
CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
66 W
0 784276 180344
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Class 2
LED
Driver
C2-
C2+
N
L
C1-
C1+
T2
T1
T1
T2
LED Driver | Pilote de LED | Controlador LED
N/C
T2
T1
N/C
T2
T1
N/C
N/C
C2
-
C2
+
Cool
C1-
C1
+
Warm
Clase P
For rated warranty tc 75 ˚C max. | Pour garantie nominale tc 75 ˚C max. |
Para la garantia nominal tc 75 ˚C max.
Case Type
• WN: W Case Type
• YS: YS Case Type
• YN: YN Case Type
LED Load Output Range: Class 2 Constant Current
(see the following pages for more detail)
• 5: 50 W Max, 0.20 – 1.50 A, 8 – 54 V-*
For rated warranty tc 70 ˚C max. | Pour garantie nominale tc 70 ˚C max. |
Para la garantia nominal tc 70 ˚C max.
lutron.com
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
ADVERTENCIA: Peligro de descarga eléctrica. Podría
ocasionar lesiones graves o la muerte. Hay presente más
de una fuente de alimentación; desconecte la alimentación
eléctrica antes de brindar mantenimiento o instalar.
l'alimentation avant d'effectuer l'entretien ou l'installation.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present,
disconnect power
before servicing or installing.
Assembled | Ensamblado | Assemble: China | Chine
C2+
C2-
C1+
C1-
N/C
N/C
N/C
N/C
T1
T2
N/C
T1
T2
N/C
L
N
t
c
T-Series
LED Driver | Pilote de LED | Controlador LED
To remove wire, insert screwdriver into slot. | Pour enlever
le fil, insérez un tourneviz dans la fente. | Para retirar el
cable, insertar destornillador en la ranura.
Cu
Al
0,35 in.
(9 mm)
Wire: Solid, 20-16 AWG, ≥ 90 ˚C
Alambre: Sólido, 20-16 AWG,
≥ 90 ˚C
Fil: Solide, 20-16 AWG, ≥ 90 ˚C
PCB
Suitable for damp locations. Indoor Use Only. | Convient aux
emplacements humides. Usage intérieur seulement. | Adecuado
para lugares humedos. Solamente para uso en interiores.
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia
sera nula si se abre la unidad.
Class B | Classe B | Clase B
Cool
Warm
Class 2
LED
Driver
C2+
C2-
T2
T1
T2
T1
C1+
C1-
N
L
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
T-Series LED Driver
PSQ02UYS-5ABLK
120 - 277 V~ CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
62 W
0 784276 180382
CLASS P
E322469
Clase P
En México: Importado Por:
Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041
Colonia Del Valle México DF. 03100 México
For rated warranty tc 70 ˚C max. | Pour garantie nominale tc 70 ˚C max. |
Para la garantia nominal tc 70 ˚C max.
lutron.com
AVERTISSEMENT : Risque d’électrocution. Peut causer des blessures
graves ou la mort. Plus d'une alimentationest présente, déconnectez
ADVERTENCIA: Peligro de descarga eléctrica. Podría
ocasionar lesiones graves o la muerte. Hay presente más
de una fuente de alimentación; desconecte la alimentación
eléctrica antes de brindar mantenimiento o instalar.
l'alimentation avant d'effectuer l'entretien ou l'installation.
WARNING: Shock hazard. May result in serious injury or death.
More than one power supply is present,
disconnect power
before servicing or installing.
Assembled | Ensamblado | Assemble: China | Chine
C2+
C2-
C1+
C1-
N/C
N/C
N/C
N/C
T1
T2
N/C
T1
T2
N/C
L
N
t
c
To remove wire, insert screwdriver into slot. | Pour enlever
le fil, insérez un tourneviz dans la fente. | Para retirar el
cable, insertar destornillador en la ranura.
Cu
Al
0,35 in.
(9 mm)
Wire: Solid, 20-16 AWG, ≥ 90 ˚C
Alambre: Sólido, 20-16 AWG,
≥ 90 ˚C
Fil: Solide, 20-16 AWG, ≥ 90 ˚C
PCB
Suitable for damp locations. Indoor Use Only. | Convient aux
emplacements humides. Usage intérieur seulement. | Adecuado
para lugares humedos. Solamente para uso en interiores.
C1= Cool White | blanc froid | Blanco frio
C2= Warm White | blanc chaud | blanco cálido
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia
sera nula si se abre la unidad.
Class B | Classe B | Clase B
Cool
Warm
Class 2
LED
Driver
C2+
C2-
T2
T1
T2
T1
C1+
C1-
N
L
T-Series LED Driver
PSQ02UYN-5ABLK
120 - 277 V~ CV
50 / 60 Hz
Output
| Sortie | SalidaInput | Entrée | Entrada
0,52 - 0,25 A Max
200 - 1500 mA CC
50 W Max
60 V- Max8 - 54 V-
Channels | Canaux |
Caneles: 2
62 W
0 784276 180382
CLASS P
E322469
Clase P
50017898
10/15/2019
Front Label Size: 4.95” x 2.77”
Corner Radius: 0.05”
Color: Pantone Process Blue, Black
Die Line - Do not print
En México: Importado Por:
Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041
Colonia Del Valle México DF. 03100 México
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico: +1.888.235.2910
4
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 5 12.17.19
“5” Output Range
Driver Type Output
Voltage
Output
Current
Output
Power
Standards
Recognition
Maximum Rated Temp.
@ t
c
for Warranty
W-Case Constant Current Driver (Class 2) 8– 54 V- 0.20 – 1.50 A* 50 W** 75 ºC
Y-Case Constant Current Driver (Class 2) 8– 54 V- 0.20 – 1.50 A* 50 W** 70 ºC
* QwikFig compatible model number PSQ02UWN-5ABLK is configurable to any current within this range in 0.005 A increments.
** Each channel is capable of delivering 50 W. The combined output of both channels must not exceed 50 W total.
277 V~ 120 V~
Parameter Value Test Conditions Value Test Conditions
W-Case
Input Current 0.25 A
V
i
= 277 V~
t
a
= 25 °C
I
o
= 0.90 A
V
o
= 54 V-
0.5 A
V
i
= 120 V~
t
a
= 25 °C
I
o
= 0.90 A
V
o
= 54 V-
Power Factor (PF) 0.95 0.99
Total Harmonic
Distortion (THD)
7% 6%
Driver Efficiency 87% 87%
Y-Case
Input Current 0.22 A 0.48 A
Power Factor 0.96 0.99
THD 9% 9%
Driver Efficiency 88% 88%
Typical Performance Specifications:
Please see graphs on the following page.
5
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 6 12.17.19
Load Compatibility
Typical THD vs Total Power Output
Typical Efficiency vs Output Current
Typical Power Factor vs Total Power Output
Output Voltage (V)
THD (%)
Efficiency at Maximum Output Power (%)
Power Factor
0.15
8
13
18
23
28
33
38
43
48
53
58
0.25
0.3 5 0.45 0.55
0.65 0.75
0.85 0.95 1.05 1.15 1.25 1.3 5 1.4 5 1.55
Output Current (A) Total Output Power (W)
Output Current (A)
Total Output Power (W)
Key: Key:
Shaded area meets both ENERGY STAR Luminaires
V2.1 Specification and DLC Version 4.3 (W case only).
Areas outside of shaded areas may not meet THD or
PF requirements.
Shaded area meets only ENERGY STAR Luminaires V2.1
Specification. Areas outside of shaded areas may not
meet THD or PF requirements.
277 V~
277 V~
Constant 25 W output Constant 50 W output
Constant 10 W output
20
80
0.95
15
60
0.90
10
40
0.85
0
0
0.75
0.70
10
0
10
15
0.3
15
20
20
25
0.6
25
30
30
25
100
1.00
35
0.9
35
40
40
50
1.5
50
45
1.2
45
5
20
0.80
“5” Output Range (continued)
Typical Performance Specifications (continued)
Key: 277 V~
277 V~
Key: W Case:
YS/YN Case:
120 V~
120 V~
277 V~
277 V~
W Case:
YS/YN Case:
120 V~
120 V~
W Case:
YS/YN Case:
120 V~
120 V~
6
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 7 12.17.19
W Case Dimensions
All measurements shown as: in (mm)
A = 16.06 (408)
B = 15.79 (401)
C = 1.18 (30)
D = 0.827 (21)
E = 0.165 (4)
F = 0.59 (15)
B
A
A
B
C
F
E
C
E
F
D
7
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 8 12.17.19
YS Case Dimensions
All measurements shown as: in (mm)
NFC
0.88
(2.25)
0.276
( 7. 0 )
1.14
(29.0)
0.71
(18.0)
0.40
(10.1)
0.87
(22.0)
0.84
(21.4)
2.22
(56.4)
0.16 (4.0 )
2.21
(56.2)
5.12 (13 0.0)
2.0 (50.8)
5.51 (140.0)
5.91 (150.0)
3.0
(76.0)
0.71
(18.0)
0.24
(6.0)
0.21
(5.4)
0.197
(5.0)
8
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 9 12.17.19
YN Case Dimensions
All measurements shown as: in (mm)
NFC
0.8
(20.4)
2.24
(57.0)
0.55
(14.0)
1.14
(29.0)
0.17
(4.2)
0.15
(3.9)
0.55
(14.0)
0.15
(3.9)
0.36
(9.2)
5.12 (13 0.0)
5.51 (140.0)
5.91 (150.0)
0.71
(18.0)
0.197
(5.0)
2.21
(56.2)
3.0
(76.0)
9
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 10 12.17.19
Wiring Diagram
To line
voltage
To digital
link
Ground
T-Series LED Driver
Ground (Green)
Line / Hot (Black)
Neutral (White)
C1+ (Red)
C2+ (Red)
C1- (Black)
C2- (Black)
Cool LED
String
Warm LED
String
T2 (Purple)
T1 (Purple/White)
Tunable White Considerations
The driver will consume two digital addresses:
Address N controls intensity*
Address N+1 controls color temperature*
The highest kelvin light source must be connected to
channel 1 (cool white).
The lowest kelvin light source must be connected to
channel 2 (warm white).
The driver can accept LED light sources with a physical
CCT value between 1500 K and 6500 K.
The driver default minimum intensity level is set to 1%.
See Tunable White Capability figure to the right for
more information.
Operation below 1% may be acceptable in some
applications. The minimum level can be adjusted below
1% through the Quantum software. See the Tunable
White Capability figure to the right for understanding the
general trade off of dimming range versus color
temperature range.
For optimal tunable white performance, it is
recommended to set high-end and low-end logical trims
which reduce the overall CCT range to less than the
maximum capability of the light source.
* This is the default behavior. During commissioning, the system may change the addresses to be non-consecutive.
Tunable White Capability
Dimming Range
Color Temperature Range
Coolest
Achievable Color
(CCT of Cool
LED String)
Recommended
minimum
light level
200 mA Operating Area
1500 mA
Operating
Area
0.1%
0.2%
1%
10%
100%
C1+ and C2+ are electrically connected inside the driver. This supports the use of common anode loads.
Warmest
Achievable Color
(CCT of Warm
LED String)
10
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 11 12.17.19
Compatible Controls: Lutron T-Series Digital Controls
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or LEDs@lutron.com
Lutron T-Series
Compatible Controls
Part Number
120 V~ 277 V~
T-Series Loops
per Control
T-Series Drivers
per Loop
Total T-Series
Drivers per
Control
T-Series Energi Savr Node* QSN-TW 2 32** 64
*
Must be used as part of a Quantum system version 3.4 or higher.
**
Each T-Series loop is capable of having 64 addresses. Each driver consumes two addresses.
11
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 12 12.17.19
T-Series Wiring
T-Series Digital Link Overview
The T-Series digital link wiring (T1 and T2) connects
the digital ballasts and drivers together to form a
lighting control system.
T1 and T2 (T-Series digital link wires) are
polarity-insensitive and can be wired in any topology
(e.g., T-tap and daisy-chain).
Power is supplied to the T-Series digital link from the
control system.
T-Series Digital Link Wiring
Make sure that the supply breaker to the drivers and
T-Series digital link supply is OFF when wiring.
Connect the two conductors to the two driver
terminals T1 and T2 as shown.
Using two different colors for T1 and T2 will reduce
confusion when wiring several drivers together.
There are two sets of T-Series digital link terminal
blocks to support daisy chaining the link.
The T-Series digital link may be wired Class 1 or
Class 2. Consult applicable electrical codes for proper
wiring practices. Please refer to Lutron Application
Note #142 (048162) at www.lutron.com for
more information.
For emergency lighting wiring, please refer to Lutron
Application Note #106 (048106) at www.lutron.com
Notes
The T-Series digital link supply does not have to be
located at the end of the digital link.
• The Maximum Wire Length table below gives the limits
for each of the wires in the T-Series digital link pair.
The T-Series digital link length is limited by the wire
gauge used for T1 and T2 as follows:
Wire Gauge Maximum Wire Length
12 AWG 1000 ft *
14 AWG 1000 ft *
16 AWG 900 ft
18 AWG 550 ft
Wire Size Maximum Wire Length
4.0 mm
2
300 m *
2.5 mm
2
300 m *
1.5 mm
2
300 m *
1.0 mm
2
207 m
0.75 mm
2
155 m
* Do not exceed cable lengths of 1000 ft (300 m).
To the T-Series digital link supply and
additional drivers
Driver Terminals
Driver Terminals
N/C
C2-
C1-
C2+
C1+
N/C
N/C
N/C
T1
T1
T2
T2
N/C
N/C
N/C
N/C
T1
T1
T2
T2
C2-
C1-
C2+
C1+
QwikFig Air
QwikFig Air
12
T-Series LED Driver
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver Tunable White
3691099h 13 12.17.19
Service
Warranty
For warranty information, please visit
www.lutron.com/driverwarranty
Replacement Parts
When ordering Lutron replacement parts, please
provide the full model number. Consult Lutron if you
have any questions.
Further Information
For further information, please visit us at
www.lutron.com or contact our LED Control Center of
Excellence at 1.877.346.5338 or LEDs@lutron.com
)Lutron, Lutron, Energi Savr Node, Quantum, QwikFig, and QwikFig Air are trademarks or registered trademarks of Lutron Electronics
Co., Inc. registered in the U.S. and other countries.
All product names, logos, and brands are property of their respective owners.
13