®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 1 09.24.19
DALI® Power Module
The DALI® Power Module is a DIN-rail mounted controller for
DALI®-compliant digital addressable loads, referred to as
control gear. It provides DALI® bus power and control for two
independent DALI® buses with up to 64DALI-compliant
digital addressable loads each.
Model Number
LQSE-2DAL-D: 2-link DALI® fixture controller
Features
Provides power for two buses of DALI®-compliant digital
addressable loads:
128 mA guaranteed current
250 mA maximum supply current per bus
Each DALI® bus can control a maximum of 16zones.
Power failure memory retains programming in
the event of a power loss.
• DALI® Power Module can be used in a HomeWorksQS
system to control and manage light in an entire home or
building.
DA 1 DA 2
NEC®
Class 2
NEC® Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CON T.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
H
M
L
LQSE-4A-D
DIN Rail Power Module
230 V~ 50 / 60 Hz 10 A
www.lutron.com +44.(0)20.7702.0657
CCI
500 W Max 800 W Max 500 W Max 500 W Max
Zone 2Zone 1 Zone 3 Zone 4
Input
Hi Temp
Prog
Power
Opt1
Opt2
Opt3
Def
Option
7
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
50017652a
EEA contact address:
Lutron EA Limited
125 Finsbury Pavement, 4th floor
London EC2A 1NQ
United Kingdom (Importer)
C
A
L
I
B
R
A
T
I
O
N
P
O
I
N
T
www.lutron.com/ChinaRohs
50
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including
interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CO NT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
Up to 64
DALI®-
compliant
digital
addressable
loads on each
bus
QS Link
DALI
® bus 1
DALI
® bus 2
Control gear
Control gear
Control gear Control gear
Power
Module
DALI®
Power Module
HomeWorks QS
Processor
GRAFIK
Eye QS
QS Contact
Closure
Interface
HomeWorks QS
Wallstation
120 / 230 V~
Control Power
Up to 100
total QS
devices
QS
Power
Supply
Sivoia QS
Shade / Drapery
DALI® Power Module (LQSE-2DAL-D)
DALI® Compatibility
The Lutron DALI
® Power Module is DALI-2® certified by the Digital Illumination Interface Alliance (DiiA)®. In order to ensure compatibility
with Lutron DALI® controllers, the connected DALI® LED drivers and fluorescent ballasts must be DALI-2® certified and marked. In
addition to compatibility, it is important to select high-quality and high-performance LED drivers and fluorescent ballasts. DALI-2®
certified devices are readily available from many manufacturers and are tested for compatibility with the standard. For a complete list of
available DALI-2® certified devices, see the DiiA® website at https://www.digitalilluminationinterface.org/products. DALI® devices that are
not listed on the DiiA® website and are not marked DALI-2® cannot be considered DALI-2® certified.
The DALI® version-1 standard does not ensure compatibility. To apply the original DALI® version-1 mark on LED drivers and fluorescent
ballasts, no verification of the test results was required, and manufacturers could self-declare compliance and apply the DAL® mark. If
you would like to use an LED driver or fluorescent ballast that is not DALI-2® certified but carries a DALI® version-1 logo, Lutron
recommends that these devices be tested to ensure compatibility. Lutron is able to perform this testing on request. Samples of the
drivers and light engines must be submitted to Lutron and the expected turnaround time is 6 to 8 weeks after the drivers are received.
Fees for testing may apply. Lutron recommends that this testing be performed before the fixtures and lighting controls are purchased
and installed. Contact your Lutron sales representative for more information.
1
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 2 09.24.19
Specifications
Power
120 V~ 50 / 60 Hz 120 mA
230 V~ 50 / 60 Hz 80 mA
Lightning strike protection meets ANSI / IEEE standard
62.31-1980. Can withstand voltage surges of up to
6000 V~ and current surges of up to 3000 A.
Stand by power: 7 W
BTUs / hour when fully loaded: 24
• DALI
® bus Output: 16V- 128 mA guaranteed supply
current, 250 mA maximum supply current per bus.
Standards
Lutron Quality Systems registered to ISO 9001:2015.
IEC 60669-2-1
• DALI-2
® Certified
• UL
• cUL
• NOM
Environment
Surrounding Air Temperature Range: 0 ºC to 65 ºC
(32 ºF to 149 ºF).
Relative Humidity: less than 90% non-condensing.
Calibration point maximum: 75 ºC (167 ºF)
For indoor use only.
Terminals
Mains Wiring: 1.0 mm
2
to 4.0mm
2
(18AWG to 10AWG)
• DALI
® bus Wiring: 0.5 mm
2
to 4.0mm
2
(20AWG to 10AWG)
QS Link Wiring: 0.5 mm
2
to 4.0mm
2
(20 AWG to 10 AWG)
• Minimum wire temperature rating = 65 °C (149 ºF),
copper wire only
Mounting
Mount in a Lutron DIN Panel (see spec 369788) or in
an IP20 (minimum) rated consumer panel or breaker
panel with integrated DIN rail.
Width = 9 DIN modules (161.7 mm or 6
3
8 in).
For more information on mounting and installation in
panels with integrated DIN rail see Lutron P/N 048466
at www.lutron.com
Programming and Compatibility Requirements
The LQSE-2DAL-D can only be used with the
HomeWorksQS system.
Setup and programming of the DALI
® Power Module
is done through the HomeWorksQS programming
software.
DALI
® Buses
Up to 64 DALI
® compliant loads on each bus can be
addressed and grouped into 16 zones.
• DALI
® Power Module supplies a maximum of 250 mA
to power each bus.
• DALI
® Power Module supplies a guaranteed current
of 128 mA to power each bus.
• DALI
® Power Module has an integrated bus power
supply with polarity indicated on the unit.
Some DALI
® loads may be polarity sensitive. Refer
to individual manufacturers' specifications for proper
connection to the DALI® bus.
Short circuit protection with automatic restart.
QS Link Limits
A QS link in a HomeWorksQS system can have up
to 512 zones (outputs) and 100devices. A DALI
®
compliant digital addressable load counts as 1 zone
unless specifically grouped into zones from the
HomeWorksQS software.
Each DALI
® Power Module counts as one device
toward the 100 device limit.
A maximum of 8 fully loaded DALI
® buses may be
connected to a single QS link.
HomeWorks QS Wallstations
HomeWorks QS wallstations can be configured to
control DALI
® Power Modules with the HomeWorks
QS programming utility.
LED indicator displays the status of programmed lights.
Troubleshooting and Maintenance
Features
Maintains redundant memory of control gear
programming for ease of single or multiple control
gear replacement.
To verify DALI
® lights connected to DALI® bus 1 and
bus 2:
Enter Test Mode: Press and hold Test button on
the DALI
® Power Module until the Test LED starts
flashing.
Test: Each press of either the DALI
® version-1 or
DALI-2® button will cycle the lights between
high-end, low-end, flash and off for that bus.
Exit Test Mode: Press and hold Test button until
Test LED stops flashing.
2
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 3 09.24.19
161.7 mm
(6
3
8 in)
60.6 mm
(2
3
8 in)
500-13431 Rev. B
N1771
Z096
89.7 mm
(3
1
2 in)
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
Overview of Wiring Terminals and Mechanical Dimensions
* Wire according to local codes.
Mains
Wiring
DALI
®
bus 1*
DALI®
bus 2*
QS
Link
IEC PELV / NEC®
Class 2
NECR Class 2
3
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 4 09.24.19
Wiring: Mains Voltage
Wiring from Distribution to Power Module
Turn off all circuit breakers or isolators feeding the
Power Module unit at the distribution panel.
Run line, neutral, and earth / ground (D) wires from a
feed to the DALI
® Power Module.
• Use 1.0 mm
2
to 4.0 mm
2
(18 AWG to 12AWG)
conductors (depending on breaker rating) to feed the
mains wiring. The device draws less than 120 mA
(120 V~) and 80 mA (230 V~).
Emergency Lighting Applications
Use normal (non-essential) power only to power the
DALI
® Power Module.
When normal power drops out, the DALI
® Power
Module will not power the DALI
® buses. When this
occurs, control gear powered from emergency feeds
go to their emergency mode (full light output by default).
Mains Wiring and IEC PELV / NEC
® Class 2
Separation
The DALI
® Power Module is designed to separate
mains wiring from IEC PELV / NEC
® Class 2 circuits.
Follow appropriate local and national codes to avoid
violating required separation guidelines.
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND. CONT.EQ.243C IN D.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
N
L
N
L
Distribution
Panel
Earth / Ground
– Neutral
Mains / Line
4
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 5 09.24.19
Wiring: DALI Bus
The DALI® Power Module will supply power for two
independent DALI
® buses, which supports a
maximum of 64 DALI
®-compliant digital addressable
loads per bus.
DALI
® Wiring
• DALI
® wiring is not SELV.
• DALI
® wiring may be treated as mains voltage, and
thus can be run within the same sheathing.
• Ensure that there is no greater than a 2 V~ drop
between the DALI
® Power Module and the end of the
DALI
® bus.
• Consult all national and local electrical codes for
separation requirements.
Wire Gauge
Maximum DALI®-compliant
Bus Wire Length
1.5 mm
2
(14AWG) 300 m (984 ft)
0.75 mm
2
(18AWG) 150 m (492 ft)
0.5 mm
2
(20AWG) 100 m (328 ft)
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND. CONT.EQ.243C IND .CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
DALI® 1
DALI
® 1
DALI
® 2
DALI
® 2
DALI
®
bus 1
DALI
®
bus 2
5
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
HomeWorks QS LQSE-2DAL-D DALI® Power Module
369650f 6 09.24.19
IEC PELV / NEC® Class 2 QS Link Wiring
Link communicates using IEC PELV / NEC
®
Class 2 wiring.
Follow all applicable national and local codes for
proper circuit separation and protection.
Wiring may be daisy chained or t-tapped.
Do NOT connect terminal 2.
Total length of QS link must not exceed 610 m
(2000 ft).
Use one, twisted-shielded pair of 0.5 mm
2
(20 AWG)
for data link (MUX, _).
QS Link
Wiring Length Wire Gauge
Available from
Lutron in one cable:
Less than
153m (500 ft)
Power (terminals 1 and 2):
1 pair 1.0mm
2
(18 AWG)
GRX-CBL-346S
(non plenum)
GRX-PCBL-346S
(plenum)
Data (terminals 3 and 4):
1 pair 0.5mm
2
(20 AWG),
twisted and shielded
153m to
610m
(500 to 2000 ft)
Power (terminals 1 and 2):
1 pair 4.0mm
2
(10 AWG)
GRX-CBL-46L
(non plenum)
GRX-PCBL-46L
(plenum)
Data (terminals 3 and 4):
1 pair 0.5mm
2
(20 AWG),
twisted and shielded
DA 1 DA 2
NEC
®
Class 2
NEC
®
Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND. CONT.EQ.243C IND .CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
(1)
(2)
(3)
(4)
COM
No Connection
MUX
MUX
DA 1 DA 2
NEC®
Class 2
NEC® Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 Nm)
L N
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50
/
60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
Wiring: QS Link
)Lutron, Lutron, HomeWorks, Sivoia, and GRAFIK Eye are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
All other product names, logos, and brands are property of their respective owners.
6