Fill - Free fillable Dci 369645a DCI Dimming Panels Spec PDF form

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 1 06.04.12

DCI Dimming Panels

DCI 1-3 Panels

Models available for:

•120V~: 1 to 3 modules (each module rated for

1200Wofincandescentload).

DCI Dimming Panels work with:

•GRX-4000ControlUnits

•GRAFIK5000

TM/6000®/7000TM Systems

•GPDimmingPanels

•LPDimmingPanels

•XPSoftswitchR Panels

•DMX512Stageboards(2LinkTMready)

Features

•IdealforMagneticResonanceImaging(MRI)Equipment

andSoundStudios.

•Providesdirectcurrent,thusnotproducingtheRadio

FrequencyInterference(RFI)thatisnormallyassociated

withstandardphase-controlincandescentdimming.

•Controlsincandescentloadsonly.

•Upto3zonesperpanel(120V~10Amodules).

•MeetsrecommendedelectricalnoiselevelsofMRI

systemmanufacturers.

•Smooth,continuousdimmingcontrolfrom0-100%

lightingoutput.

•Lampsarefreefromanyaudiblenoiseandflicker

throughouttheentiredimmingrange.

•Thedimmingmodulesfeatureanair-gapinoffswitch

thatstopsallpowertotheincandescentloads.

•Electricityissavedproportionallyasthelightlevelis

reduced.

Benefits

MRI Room:

•Acomfortablelightlevelsettingforpatientsduring

examination.

•Reducesglareontheglassseparatingthecontrol

roomfromtheMRIroom,aswellasontheequipment

monitorscreen.

•AdjustablelightlevelsfacilitateinspectionoftheMRI

roombyhospitalpersonnelandpatientspriortouse.

Sound Studio:

• Lampsarefreefromanyaudiblenoisecausedby

standardphase-controldimming.

•DoesnotproducetheRadioFrequencyInterference

(RFI)emissionscausedbytypicaldimming,whichcan

coupleontomicrophonesandrecordingequipment.

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 2 06.04.12

Setup

 Circuitselectorelectronically

assignscircuitstozonesand

sources.Permitsreassignment

ofzonesandsourceswithout

rewiring.

Physical Design

•Enclosure:NEMA-Type1,IP-20

protection;16U.S.GaugeSteel.

Indoorsonly.

•Weight:130to210lb(59to

95kg).

•Mounting:Surfacemountonly.

Allowspaceforventilating.

•SeismicCertificationLimits:

=2.5g,z/h=1.0,I

=1.5.

ContactLutronfordetails.

Environment/Heat Dissipation

•Patented,ribbedaluminum

heatsinkbasecoolspanelby

convection.Nofans.

•32to104°F(0to40°C).Relative

humiditylessthan90%

non-condensing.

MRI Installations Requirements

•MRIinstallationsrequireoneofthe

following:

 1)Onecustomfacilityfilterper

output

 2)Onestandardfacilityfilter

peroutputANDoneisolation

transformerpersingle

phaseinput.

•Facilityfiltersandisolation

transformersmustbeprovidedby

others.

•SeeWiringOverviewpageformore

information.

Specifications

Standards

•

ULRListed(Reference:ULFileE42071)

•CSACertied

•

CaliforniaEnergyCommissionListed

•SeismicCertied(TestMethod

AC156.ReferenceOSHPD

PreapprovalOSP-0215-10)

•Othercerticatesmayapply

Power

•Inputpower:120V~ 60Hz,

phase-to-neutral.

•Output:ContinuouslyvariableDC

from30to110V-.

•MainCircuitBreakers:UL-rated

thermalmagnetic.

AICrating:10,000

•Lightningstrikeprotection:Meets

ANSI/IEEEstandard62.41-1980.

Canwithstandvoltagesurgesofup

to6000Vandcurrentsurgesofup

to3000A.

•Powerfailurememory:

Automaticallyrestoreslightingto

thesceneselectedpriortopower

interruption.

Sources/Load Types

 Operatesincandescentloadswith

asmoothcontinuousSquareLaw

dimmingcurve.

Wiring

•Internal:PrewiredbyLutron.

•Systemcommunications:low-

voltageIECPELV/NECRClass2

wiringconnectsDimmingPanelsto

othercomponents.

•Line(mains)voltage:Feed,load,

andcontrolcircuitwiringonly.No

otherwiringorassemblyrequired.

Dimming Modules

•Eachmodulehasamaximum

outputof1200W(10Aat

120V~).Upto3modules

perpanel

•Incorporateover-voltagefeedback

circuitrythatsensestheDC

outputvoltageandlimitsittoa

maximumof116V-evenifload

isreduced.Thiscircuitryshall

preventprematurelampfailures

fromoccurringonlightlyloaded

circuits.

•Includeback-upovervoltage

feedbackcircuitrythatshall

disconnectthedimmingmodules

fromtheloadiftheloadis

reducedandprimaryover-voltage

feedbackcircuitrymalfunctions.

Thispreventsanypermanent

arcingassociatedwithDCcircuits.

•MaximumACripplevoltage

permittedonthevariableDC

outputshallbe5V~throughout

thedimmingrange.

•Incorporateasoft-startcircuit

tosuppressthelargein-rush

currentsassociatedwithturning

onacoldlamp.

•Includeoutputfusesinserieswith

bothoutputloadwires.Fuses

mustbedesignedtointerrupta

110V-currentover12A.

•RTISS

TMfiltercircuittechnology

compensatesforincomingline

voltagevariations:Novisible

flickerwith+/-2%changein

RMSvoltage/cycleand+/-2%Hz

changeinfrequency/second.

•RFIsuppressioncircuitryprovided

tominimizeinterferancewithMRI

andSoundStudioequipment.

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 3 06.04.12

Anatomy of a DCI Model Number

Wire Sizes

Input Feed Wiring

 Power(Hot/Live)andNeutralconnecttoTerminalBlocks

14AWG(2.0mm

)to10AWG(4.0mm

Load Circuit Wiring

 Loadft+ftandft-ftconnecttoFuseTerminalBlocks

14AWG(2.0mm

)to10AWG(4.0mm

DCI 1 1Ø,2W 20A  20A  OneMain DCI1-1202M-20

          Breakerper

Module.

 DCI2  1Ø,2W 20A  20AX2 InputFeed DCI2-1202M-20

          Terminates

          atTerminal

 DCI3  1Ø,2W 20A  20AX3 Blocks DCI3-1202M-20

 Numberof  Feed  Maximum Main  Panel  Model

 Dimming  Type  Feed  Circuit  Feed  Numbers

 Modules      Breaker

DCI2-1202M-20

Prefix

Voltage

FeedType

PanelFeed

MainBreaker

Rating

Prefix:

DCIforDCIDimmingPanel.

Number of Dimming Modules:

 Indicatesnumberofdimmingmodulesinthepanel

(1,2,or3modules).

Voltage Input:

120for100-127V~.

Feed Type:

2for1phase2-wire.

Panel Feed:

MforMainBreaker-oneMainBreakerpermodule.

 Inputfeedterminatesatterminalblocks.

Branch Circuit Breaker Rating:

20for20AMainCircuitBreakers.

Numberof

Dimming

Modules

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 4 06.04.12

13 in

(330 mm)

12 in

(304 mm)

12 in

(304 mm)

2 in

(51 mm)

2 in

(51 mm)

2 in

(51 mm)

35 in

(889 mm)

33 in

(825 mm)

41 in

(110 mm)

275 in

(700 mm)

4 in

(100 mm)

Front View

Top View

Right Side ViewLeft Side View

Bottom View

Load Circuit WiringFeed Wiring

Removable

Top Cover

IEC PELV/

NECR Class 2

wiring only -

7/8 in (22 mm)

diameter

7% in

(195 mm)

Keyhole accepts a maximum

of 5/16 in (8 mm) mounting bolt.

1/4 in (M6) recommended.

Punch holes as necessary for

Feed and Load Circuit Wiring

371 in

(946 mm)

FeedandLoadCircuitWiring

toentertopofpanel

Dimensions for DCI 1-3 Panels

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 5 06.04.12

PANEL MAXIMUM  WEIGHT

 BTUs/H (WITHOUTPACKAGING)

DCI1 260  130lb(59kg)

DCI2 515  170lb(77kg)

DCI3 770  210lb(95kg)

Mounting for DCI 1-3 Panels

Surface mount indoors

•Panelgeneratesheat.Mountonlywhereambient

temperaturewillbe32to104°F(0to40°C).

•Thisequipmentisaircooled-ventsmustnotbe

blockedoryouwillvoidthewarranty. Leave12in

(31cm)clearancesabove,below,andinfrontof

panel.Noclearancenecessaryonsides.

•Reinforcewallstructureforweightandlocalcodes.

WiringRaceway

air

flow

Terminalsfor

LoadCircuits

12in(31cm)

minimum

topandfront

12in(31cm)

minimum

Warning:ShockHazard.Toavoidtheriskofelectricshock,installpanelswheretheywillnotgetwet.

Waterdamagespanels.

DCI 1-3FrontView DCI 1-3SideView

MaximumFeedandWireSizes-

ConsultWiringOverviewpage.

•DimmingPanelswillhumslightlyandinternalrelays

willclickwhileinoperation.Mountwhereaudible

noiseisacceptable.

•MountPanelssoline(mains)voltagewiringisatleast

6ft(1.8m)fromsoundorelectronicequipmentand

wiring.

•Panelsmustbemountedwithin7°oftruevertical.

IECPELV/

NECRClass2

Wiring

Feedand

LoadCircuitWiring

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 6 06.04.12

IECPELV/

NECRClass2

Wiring

IECPELV/

NECRClass2

Wiring

6in(16cm)

minimum*

WiringRaceway

airflow

12in

(31cm)

minimum

3ft45in

(103cm)

mounting

holes

6ft6in

(195cm)

NEC

Breaker

Height

Limit

7ft55in

(228cm)

mounting

holes

8ft8in

(265cm)

minimum

toceiling

about12in

(31cm)

* 6in(16cm)approvedforthislayoutonly.

DCI 1-3FrontView

Mounting One Panel Above Another

 Youneedatleast8ft8in(265cm)betweenthefloorandthe

suspendedceilingforthislayout.

DCI 1-3SideView

Warning:ShockHazard.Toavoidtheriskofelectricshock,installpanelswheretheywillnotgetwet.

Waterdamagespanels.

Feedand

LoadCircuitWiring

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 7 06.04.12

DCI 1-3 Wiring Overview (MRI Rooms only)

NOTICE:AllControlsandDimmingPanelsmust

bemountedoutsidetheMRIroom,awayfromthe

influenceoflargemagneticfields.

NOTICE: AllvoltagesuppliesintoanMRIroom

mustbefedthroughfacilityfilters.LutronR DCI

PanelsrequirethefollowingULRListedfilter:

FIL-COILCOMPANY,INC.

P/NFC-2249

631.467.5328

Pleasenotethatthisisacustomfilterdesigned

specificallyforDCIPanels.

OtherfiltersarenotpermittedunlesseachDCI

circuitissuppliedbyaseparate120:120,3.0kVA

isolationtransformer(onetransformerisrequired

foreachpowerinput).

Failuretouseoneoftheabovemethodswillresult

invoidingofthewarranty.

Wiring with Fil-Coil Facility Filter

ModulePrewired

byLutron

Fuses

InputFeed

120V~

Incandescent

Load

*FacilityFilter:

Fil-CoilFC-2249

byothers-one

requiredpercircuit

Input

Breaker

Wiring with any Facility Filter

ModulePrewired

byLutron

Fuses

InputFeed

120V~

Incandescent

Load

*StandardFacility

Filterbyothers-one

requiredpercircuit

Input

Breaker

Isolation

Transformer

byothers

Isolated

Feed

Note on Isolation Transformers - Keep Each Module Feed Separate from Each Other

Feed1

Feed2

Feed3

Module 1

Module2

Module 3

Module 1

Module2

Module 3

Phase

Feed

than one

Module

Phase

Feed

3 Phase

Modules

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 8 06.04.12

InputBreaker(s)

PrewiredbyLutron:

 

 

DCI 1-3 Wiring Overview

WIRE SIZES

Feed Wiring

 ConnecttoTerminalBlocks.14AWG

(2.0mm

)to10AWG(4.0mm

Load Circuit Wiring

 ConnecttoFuseTerminalBlocks.

14AWG(2.0mm

)to10AWG

(4.0mm

Control Wiring

 ConnecttoCircuitSelector.Seelow-

voltageIECPELV/NECRClass2wiring

onnextpage.

 Powerandcontrolwiresmustberun

inseparateracewaystoensureproper

operationofcontrols.

FeedWiringtoInput

TerminalBlocks

LoadWiringtoOutput

FuseHolders

ControlBreaker

GahuntaParts

Assembly(GPA)

Dimmer

OverVoltageCard

CircuitSelector

Note:Panelsarenotdesignedforsideorbottomentryoffeedorloadwires

Troubleshooting Tips:

•CycletheappropriateinputbreakertoresettheOvervoltageCard.Atypicalreasonfortrippingistheload

currentquicklyreducingduetoalampblowout.

•ThefirstinputfeedpowersthefirstmoduleANDthecontrolcircuitry.WhileBreaker‘C’isOff,alloutputswill

freeze.Cyclinganinputbreakerwillthenbringtheappropriateoutputtofull.

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 9 06.04.12

Low-Voltage IEC PELV/NECR Class 2 Wiring

Systemcommunicationsuselow-voltageIECPELV/NECRClass2wiring.

Mustbedaisy-chained.

Mustrunseparatelyfromline(mains)voltage.

GRAFIKEye

4000System

IECPELV/NECRClass2wiringlinkrequires:

Two12AWG(2.5mm

)conductorsforcontrolpower.

Onetwisted,shieldedpairof18AWG(1.0mm

)fordatalink.

One18AWG(1.0mm

)conductorforEmergency(Essential)senseline,frompaneltopanel.

TotallengthofControlLinkmaybenomorethan2000ft(610m).

Approvedlow-voltagecableisavailablefromLutron,

Belden,andLiberty.Theseareapprovedwith22AWG

datalinkwires.

GRAFIK5000TM/6000®/7000TM System

IECPELV/NECRClass2wiringlinkrequires:

Two12AWG(2.5mm

)conductorsforcontrolpower.

Onetwisted,shieldedpairof18AWG(1.0mm

)fordatalink.

One18AWG(1.0mm

)conductorforemergency(essential)senseline,frompaneltopanel.

TotallengthofControlLinkmaybenomorethan2000ft(600m).

IfMUX-RPTRinterfaceandGRX-CBL-46Lcable

isused,lengthmaybeupto4000ft(1200m).

GRX-CBL-46L IECPELV/NECRClass2wiringcableisavailablefromLutronandcontains:.

 Two12AWG(2.5mm

)conductorsforcontrolpower.

 Onetwisted,shieldedpairof22AWG(0.625mm

)fordatalink.

 One18AWG(1.0mm

)conductorforemergency(essential)senseline.

ControlUnit

Control Interface

DimmingPanels

Wallstations

ControlUnit

Control Interface

RefertoGRAFIK5000T/6000R/7000TSpecification

PowerPanelLink

DimmingPanels

Processor

Panel

Wallstations

PowerPanelLink

WallstationLink

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 10 06.04.12





























Data A OK

Power

Common

24VFW

MUX

Drain

Sense

 





Data B OK



Comm

Drain

MUX





Link



Link

 













Data A OK

Power

Common

24VFW

MUX

Drain

Sense







Data B OK



Comm

Drain

MUX





Link



Link









Data A OK

Power



Common

24VFW

MUX

Drain

Sense

 





Data B OK



Comm

Drain

MUX





Link







Link

IEC PELV/NECR Class 2 Panel-to-Panel Wiring

Toadditional

PowerPanels

ControlWiring

(2)12AWG

(2.5mm

)

1: Common

2:24VFW

DataLink

(1)shielded,

twistedpair

18AWG

(1.0mm

)

3:MUX

4:MUX

(1)18AWG

(1.0mm

)

5:SenseLine

LightingControls

or Processors

Shield/Drain

PowerPanel1

PowerPanel2

Notes:

1.EmergencyPower:Theadditional18AWG(1.0mm

)wire

isainsenseinlinefromterminal5ofanotherPanel.This

senselineallowsanEmergency(Essential)LightingPanel

toinsenseinwhenNormal(Non-Essential)powerislost.If

morethanoneEmergencyLightingPanelneedstosense

fromaspecificNormalPanel,adedicatedwirebetween

eachpairofNormal(Non-Essential)andEmergency

(Essential)panelsmayberequired.Forapplicationsrequiring

UL924listedproduct,usetheLUT-ELI-3PHEmergency

LightingInterfacetodrivethesenseline.

2.Shield/Drain:Connectshieldingasshown.Donotconnect

toGround(Earth)orcircuitboardofCircuitSelectorConnect

thebaredrainwiresandcutofftheoutsideshield.

(4)12AWG(2.5mm

)

IEC PELV/NECR Class 2 Terminal Connection

 Eachlow-voltageIECPELV/NECRClass2terminalcan

acceptonlytwo18AWG(1.0mm

)wires.Two12AWG

(2.5mm

)conductorswillNOTfit.Connectasshownusing

appropriatewireconnectors.

Shield/Drain

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

GRAFIK SystemsT DCI Dimming Panels Power Equipment

369-645a 11 06.04.12

IEC PELV/NECR Class 2 DMX512 to Link B

























 

















































Tonextpanel

ToDMX512

Stageboard

Wiresmustbedaisychainedandcappedoffat

bothendsofLinkB.

Notes:

1.Wireindaisy-chainconfigurationasfollows:C to C,+ to +,and- to -.

2.UsecablerecommendedbyStageboardmanufacturerorfromLutronasGRX-CBL-DMX-250/500.

3.AllCircuitsdefaulttocontrolbythefirstzoneofLinkA.SeeinstructionsforassigningLinkHierarchytoallowa

CircuittobecontrolledbyeitherLinkBalone,orconditionallybyLinkAorLinkB.

Fill Online, Printable, Fillable, Blank Dci 369645a DCI Dimming Panels Spec Form

Related forms

Fillable Dci 369645a DCI Dimming Panels Spec

Fill Online, Printable, Fillable, Blank Dci 369645a DCI Dimming Panels Spec Form

Related forms

First 20 documents completely FREE!