Fillable SZ 1SD Lamp Socket Dimmer Switch

Fill Online, Printable, Fillable, Blank SZ 1SD Lamp Socket Dimmer Switch Form

Use Fill to complete blank online LUTRON ELECTRONICS, INC. pdf forms for free. Once completed you can sign your fillable form or send for signing. All forms are printable and downloadable.

SZ 1SD Lamp Socket Dimmer Switch

On average this form takes 16 minutes to complete

The SZ 1SD Lamp Socket Dimmer Switch form is 9 pages long and contains:

  • 0 signatures
  • 0 check-boxes
  • 63 other fields

Country of origin: US
File type: PDF

Use our library of forms to quickly fill and sign your Lutron Electronics, Inc. forms online.

BROWSE LUTRON ELECTRONICS, INC. FORMS

Related forms
Fill has a huge library of thousands of forms all set up to be filled in easily and signed.
Fill in your chosen form
Sign the form using our drawing tool
Send to someone else to fill in and sign.
find another form
 
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 1 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Lamp Socket Dimmer/Switch
Description
The Stanza system is an easy-to-install and easy-to-use lighting
control system designed especially for hotel guest rooms and similar
applications. The system consists of wallbox dimmers, wallbox
switches, line-voltage wallbox keypads, low-voltage interfaces, and
lamp socket dimmer/switches. All of these devices communicate via
radio frequency (RF) within each individual guest room.
Stanza lamp socket dimmer/switches allow guests to control a
local lamp by rotating the knob at the socket. They can be controlled
remotely via other Stanza components.
Features
• Fits standard Edison medium-bore (E26) lamps.
• Allows local dimming control of halogen and incandescent lamps,
and switching (toggle On/Off) control of compact fluorescent lamps.
• Light level can also be adjusted, if addressed as part of a Stanza
lighting control system, via an RF command from a keypad or
integration device.
• Provides auditory feedback when knob is rotated.
• Lamp harp locking mechanism (provided) deters theft.
• Large knob designed with ADA and Universal Design considerations.
Design Considerations
• The lamp socket dimmer/switch cannot be used on lamps with
integral dimmers.
• For lamps with integral switches, the integral switch must be left in
the “on” position for proper operation.
• Ensure that proper space exists in the lamp harp and from the bulb
to the shade of the lamp being used. See “Installation Notes” in this
document and Lutron Application Note #243 at www.lutron.com for
more information.
• Always use a bulb that remains within the wattage rating of the table
or floor lamp.
SZ-1SD
1
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 2 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Specifications
Standards:
• UL listed to standard 496 “lampholders”
• NOM listed to standards NOM 003 and NMX508
• CUL listed to standard C22.2 no. 43,
lampholders, and ICA registered
• FCC approved. Complies with the limits for a
Class B digital device, pursuant to Part 15 of the
FCC rules
Power:
• Operating voltage: 120 V 50/60 Hz
Non-permanently connected fixtures only
Load:
• Always use a bulb that remains within the wattage
rating of the table or floor lamp.
• 10 W minimum for incandescent, halogen, and
fluorescent. For base-down orientation, maximum
150 W incandescent, 100 W halogen, and
30 W fluorescent. (See Derating under Installation
Notes if not installed base-down.)
• Dims a single halogen or incandescent bulb
• Can be configured to switch a single compact
fluorescent bulb
Key Design Features:
• Unit ships from factory as a switch and must be
configured to control dimmable loads when the
system is commissioned
• Green LED status indicator shows current load
status
• LED turns amber for programming indication
• LED turns red and turns off load output if an
over-temperature condition is detected
• Adjustable maximum light level provides energy
savings and extended bulb life
• Power failure memory: if power is interrupted,
when the power is restored, lamp will return to its
previously set level prior to the interruption
• Light level can be fine-tuned by rotating the knob
until the desired light level is reached (dimmable
loads only)
• Lamp socket dimmer/switch must be installed
below or beside bulb, not above bulb
• Dimensions: 1.85 in (47 mm) wide
3.74 in (95 mm) deep
1.6 in (41 mm) added height above
socket
System Communication and Capacity:
• Lamp socket dimmer/switches communicate with
other Stanza system components through radio
frequency (RF) at 434 MHz
• Multiple RF channels and thousands of system
addresses prevent interference between systems
• Each lamp socket dimmer/switch counts as 1
toward the single-system maximum of 31 Stanza
devices
(Maximum devices can be increased to 100 if an
SZ-CI-PRG is present in the system)
Environment:
• Ambient operating temperature:
32 - 104 °F (0 - 40 °C)
• Maximum 90% non-condensing relative humidity
• Indoor use only
Warranty:
• 1-year limited warranty
• 2-year full parts and labor warranty, with 8-year
pro-rated parts replacement on commissioned
systems
Color/Finish Codes:
Taupe only
2
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 3 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Mounting and Dimensions
1.6 in (41 mm)
added to bulb height
3.74 in
(95 mm)
1.85 in
(47 mm)
Installation Notes
WARNING! RISK OF FIRE
It is important to maintain proper spacing between the bulb and the lamp shade. When the lamp socket
dimmer is installed, spacings A and B (as seen in the diagram below) should be equal to or greater than
required by the original UL listing for this portable lamp. Portable lamps are listed to UL 153, “Portable
Electric Luminaires”. This standard specifies minimum spacings for A and B based on the construction of the
lamp and the rated wattages of acceptable bulbs. Consult the lamp manufacturer for this information. Lutron
recommends that the spacings with the lamp socket dimmer installed be equal to or greater than what they
were without the lamp socket dimmer installed. This may require a new lamp harp. See Lutron Application
Note #243 at www.lutron.com for more information.
is the spacing to the top of the shade
(this applies only to shades with a closed top)
is the spacing to the nearest point of the shade
UL Listing of Portable Lamps with Lutron’s Lamp Socket Dimmer
Lutron’s lamp socket dimmer is UL listed to standard #496, “Lampholders”, while portable lamps are
UL listed to standard #153, “Portable Electric Luminaires”. A portable lamp with the lamp socket dimmer
pre-installed by the lamp manufacturer can be UL listed as an assembly under UL 153. For more information,
contact your portable lamp manufacturer.
A
B
A
B
A
B
3
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 4 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 4 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Installation Notes (continued)
• Always use a bulb that remains within the wattage
rating of the table or floor lamp
• Unplug fixture before installing lamp socket
dimmer/switch or changing bulb
• To install lamp socket dimmer/switch, remove bulb
from socket, screw lamp socket dimmer/switch
into lamp socket, then replace bulb in lamp socket
dimmer/switch socket
• Lamp harp may need to be removed during
installation
• Mount lamp socket dimmer/switch between
base-down and horizontal
• Slide harp lock onto bottom of harp and tighten
with 1/16 in (1.5 mm) hex wrench (not provided)
Allowable mounting orientations:
Base-down to horizontal
These mounting orientations not allowed
Derating
Orientation Rating
Base-down 150 W incandescent
100 W halogen
30 W compact fluorescent
From base-down to
horizontal
100 W incandescent
75 W halogen
30 W compact fluorescent
Harp lock
Hex
wrench
Lamp
socket
dimmer/
switch
4
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 5 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Potential Lamp Harp Interference Issues
The Lutron Lamp Socket Dimmer/Switch is designed to fit in a large variety of typical table and floor
lamps. However, due to the large variability in lamp designs, the Lamp Socket Dimmer/Switch may not
fit into all lamps.
There are three main scenarios where the Lamp Socket Dimmer/Switch may not fit into a lamp that
uses a lamp harp to support the shade. Please refer to the “Terminology” section on the last page for a
definition of terms.
These can be addressed with proper selection and installation of a compatible harp or proper alignment of
the harp parts.
Harp not aligned
Figure 3
Harp too short
Figure 1
Harp too narrow
Figure 2
5
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 6 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Solutions
Harp too short (Figure 1)
The Lamp Socket Dimmer/Switch adds approximately 1.6 in (41 mm) of height to a standard bulb. In
some cases, this may cause the top of the bulb to come into contact with the top of the lamp harp. This
can be fixed by using a taller harp or a shorter bulb. Note that the bulb socket height is not standard, and
may vary from one lamp design to another.
Harp too narrow (Figure 2)
Some lamp harps may not be able to accommodate the Lamp Socket Dimmer/Switch because it is wider than a
typical bulb at the base. This problem may also occur when compact fluorescent bulbs (CFLs) are used with these
harps. If this problem is experienced, Lutron recommends using a lamp harp that was designed to work with CFLs.
Harp not aligned (Figure 3)
When screwing in the Lamp Socket Dimmer/Switch to the lamp, the knob may end up in an undesirable direction,
such as facing the back of the lamp, or the direction of the Lamp Socket Dimmer/Switch may prevent proper re-
installation of the lamp harp.
Correcting this problem requires re-aligning the harp with the Lamp Socket Dimmer/Switch. In some lamp designs,
the bulb socket may be turned slightly by grasping the socket and applying firm force to twist the socket clockwise
or counterclockwise as necessary. DO NOT apply pressure to the Lamp Socket Dimmer/Switch to twist the bulb
socket. Doing so may damage the socket or Dimmer/Switch. You may need to loosen a set screw located at the
base of the bulb socket in order to rotate it.
Typically, the lamp harp can be rotated by firmly grasping the harp saddle and applying firm force to
twist the saddle clockwise or counterclockwise as necessary. You may need to loosen a nut located
between the bulb socket and harp saddle or harp saddle and lamp in order to rotate the harp saddle.
Resources
Lutron has tested the following lamp harps to properly fit the Lutron Lamp Socket Dimmer/Switch. This is
not an exhaustive list, but is meant as a guide to help if an issue is experienced. As a convenience to our
customers, Lutron offers a selection of harps available for purchase. Please contact Lutron customer service
(1.888.LUTRON1) or visit www.lutronstore.com to order.
Harp Size Harp Color Manufacturer Model Number Lutron Part Number
7 in (178 mm)
Brass Satco 90-919 −−−
Nickel Satco 90-2000 −−−
8 in (203 mm) Brass Satco 90-920 Lutron LH-8PB
Nickel Satco 90-2001 Lutron LH-8PN
9 in (229 mm) Brass Satco 90-921 −−−
Nickel Satco 90-2002 −−−
10 in (254 mm) Brass Satco 90-922 Lutron LH-10PB
Nickel Satco 90-2003 Lutron LH-10PN
6
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 7 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
Dimmer Operation
Dimming Knob
Turn clockwise to turn on and brighten
Turn counter-clockwise to dim and turn off
Push in to toggle on and off
Distinct sounds indicate when high or low level is reached
Status Indicator
Indicates current load status with green indicator
Green = load is switched on
Green Nightlight = load is switched off
Amber = device is in programming mode
Red = device is experiencing an over-temperature condition
Dimming
knob
Status
indicator
Over-temperature Detection
If an over-temperature condition is detected, the LED on the lamp
socket dimmer/switch will turn red, and the lamp socket dimmer/
switch will turn off the bulb. Proper installation and conformance to
all specifications should be ensured before proceeding. To return the
device to normal operation, perform the following:
• Cycle power to the device (unplug the lamp; cycle the circuit breaker)
• Within the first 2 minutes of restoring power, press and hold the
dimming knob for 3 seconds. The LED should turn from red to green.
7
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 8 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
System Communication Notes
• Stanza RF devices must be located within 30 feet
(9 m) of a Stanza device configured as a repeater.
Multiple devices configured as repeaters may be
necessary to provide adequate coverage.
• Any Stanza device can be configured as a
repeater.
• A total of 5 devices maximum can be configured
as repeaters.
• Devices configured as repeaters must be within
30 feet (9 m) of another device configured as a
repeater.
• Stanza lighting controls cannot be controlled
wirelessly and Stanza keypads will not function
until they are addressed and programmed.
System Overview
Dimmer
Keypad
30 ft (9 m) max. from
repeater device
30 ft (9 m) max. from
repeater device
30 ft
(9 m) max.
Feature Basic System
(no SZ-CI-PRG present)
Advanced System
(with SZ-CI-PRG present)
Maximum devices 31 100
RS232 and/or Ethernet
Interface Capability
No Yes
PC Required for Device
Replacement
No Yes
System Limits
8
R
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
sz-1sd 9 01.14.10
Wireless Lighting Control
Lamp Socket Dimmer/Switch
StanzaTM
a) Harp
(supports shade)
b) Bulb
c) Lamp
Socket Dimmer/
Switch
Terminology
d) Bulb Socket
e) Harp Saddle
(supports harp)
Lamp harp height is
determined by the
distance between
the top of the harp
and the bottom of
the saddle.
f) Socket Set Screw
g) Mounting Nut
9
Download
Save PDF to desktop
Email
Email completed PDF
Send for Signing
Email for others to sign
Print
Print document
Choose a Field
Click on a field and
select the person that should complete it
Want to add a signature?
You can add a signature field
and assign it to someone else
to sign
Choose a Field
Click on a field and
select the person that should complete it

SZ 1SD Lamp Socket Dimmer Switch

This document is locked as it has been sent for signing.

You have successfully completed this document.

Other parties need to complete fields in the document. You will recieve an email notification when the document has been completed by all parties.

This document has been signed by all parties.

Completed 8 May 2020

Message

View Audit Log
Print With Audit Log
Duplicate Document