®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369369 Rev. B 1 06.02.11
Control Interfaces
OMX-CI-NWK-E
GRAFIK SystemsTM
OMX-CI-NWK-E Control Interface
Description
•IntegratesGRAFIK5000TM, GRAFIK 6000®,
GRAFIK 7000TM, Softswitch128®, and LCP128®
systems with a touchscreen or other digital
equipment that supports TCP/IP communication
over Ethernet.
•Providesmonitoringcommandsthatallowa
touchscreen to query lighting systems to:
Determine which scene is selected.
Keep track of buttons pressed.
•Providescontrolcommandsthatallowa
touchscreen or PC to operate lighting systems to:
Select or sequence lighting scenes.
Raise or Lower one or more zones.
Activate panic mode (lights go to full on).
Simulate button actions
Disable or Enable timeclock(s)
1
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369369 Rev. B 2 06.02.11
Control Interfaces
OMX-CI-NWK-E
GRAFIK SystemsTM
Power
•IECPELV/NEC® Class 2
•OperatingVoltage:12V 125mA
24V 65mA
Uses OMX RS232 Command Set
•Monitoring:Sceneselectionandscenestatusupdates.
•Control:Sceneselection,scenelockout,sequencing,zonelockout,zoneraise/lower.
System Communications and Capacity
•IECPELV/NEC® Class 2 wiring connects OMX-CI-NWK-E Interface to Processor Panel.
•StandardCAT5cable,328ft(100m)maximum,connectsOMX-CI-NWK-EInterfacetoPCorother
Ethernet source.
•SupportsMDI/MDIXauto-crossover(nocrossovercableneeded).
•MultipleControlInterfacesmaybeusedinasinglesystem.
Environment
32 to 104 °F (0 to 40 °C). Relative humidity less than 90% non-condensing.
Specifications
Dip Switch Settings
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
ON
ON
ON
ON
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
Address
Switch Settings
Address
Switch Settings
Address
Switch Settings
Address
Switch Settings
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
ON
ON
ON
ON
1 2 3 4 5 6
ON
7 8
1 2 3 4 5 6
ON
7 8
Up Down
(On) (Off)
Addressing
Not used
2
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369369 Rev. B 3 06.02.11
Control Interfaces
OMX-CI-NWK-E
GRAFIK SystemsTM
Dimensions
2.47 in
(62.7 mm)
3.75in
(95.3mm)
4.26 in
(108.2 mm)
5.26in
(133.6 mm)
1.06 in
(26.9 mm)
Mounting
Holes
Mounting
1. Mount the control interface directly on a wall, as
shown in the Mounting Diagram, using screws (not
included). When mounting, provide sufficient space
for connecting cables.
The unit can also be placed in the LUT-19AV-1U AV
rack using the screws provided with the unit. The
LUT-19AV-1U will hold up to four units.
If conduit is desired for wiring, the LUT-5x10-ENC
can be used to mount one unit.
2. Strip 4 in (10 mm) of insulation from wires. Each
data link terminal will accept up to two 18 AWG
(1.0 mm
2
) wires.
3. Connect wiring as shown in the Wiring Diagram
(next page). LED 1 lights continuously (Power) and
LED 7 blinks rapidly (Data Link RX) when the IEC
PELV/NEC® Class 2 Data Link is installed correctly.
LUT-19AV-1U
Wire Strip Length
4 in
(10 mm)
5.26
4.263.75
2.50
1.06
Control Interface
Wall
Mounting Diagram
LUT-5x10-ENC
0.25
(6.4)
0.34 (8.6)
dia.
0.18 (4.6)
dia.
0.18 (4.6)
dia.
#6 or #8 (M3 or M4)
screw recommended
(not included)
Mounting Hole Detail
Dimensions: in (mm)
3
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369369 Rev. B 4 06.02.11
Control Interfaces
OMX-CI-NWK-E
GRAFIK SystemsTM
Ethernet Link Wiring
•StandardCAT5cableconnectsOMX-CI-NWK-EInterfacetoPC,router,orother
Ethernet source.
•Nocrossovercableneeded.
•Mustbe328ft(100m)orless.
•Ethernetnetworkandcableprovidedbyothers.
RJ45 jack:
Ethernet Link
(to PC or
A/V equipment)
Ethernet link/
activity
Ethernet
speed
Data Link (to
Control Units,
processors,
and
wallstations)
DIP Switches
LED 1: Power
LED 2: Ethernet link
LED 3, 4, 5: Unused
LED 6: Data link TX
LED 7: Data link RX
CAT5 Cable:
maximum 328 ft
(100 m)
To PC or AV Equipment. For Ethernet Link, use CAT5
cable provided to connect to auxiliary equipment. The
Ethernet Link LED will light continuously when link is
present and will flash when there is link activity. Additional
Ethernet network equipment and cables provided by others.
12 or 24 V to outlet (with optional
transformer). Do not wire terminal 2 on Data
Link when using optional transformer. To
power separately from the Data Link, order the
following Lutron transformer model numbers:
120 V : T120-15DC-9-BL
240 V : TE240-15DC-9-BL
240 V (UK): TU240-15DC-9-BL
1 2 3 4 5 6 7
•Daisy-chaintheOMX-CI-NWK-EInterfacetotheIECPELV/NEC® Class 2 Wallstation
Link that connects to the Processor Panel.
•Makedaisy-chainconnectionstotheIECPELV/NEC® Class 2 Data Link terminals on
the front of OMX-CI-NWK-E Interface.
•DonotuseT-taps.Runallwiresinandoutofterminalblock.
•Eachterminalacceptsuptotwo18AWG(1.0mm
2
) wires.
•LED1lightswhentheIECPELV/NEC® Class 2 Data link is installed correctly.
•ConsultProcessorPanelSpecificationSubmittalformoredetails.
IEC PELV/NEC® Class 2 Wiring
4
®
Job Name:
Job Number:
Model Numbers:
Page
SPECIFICATION SUBMITTAL
369369Rev.B506.02.11
Control Interfaces
OMX-CI-NWK-E
GRAFIK SystemsTM
•Two12AWG(2.5mm
2
)conductorsforcommon(terminal1)and24V (terminal 2).
These will not fit in terminals. Connect as shown. Ensure that the terminal 2 connection
is wired when not using optional transformer.
•Oneshielded,twistedpair18AWG(1.0mm
2
) for data link (terminals 3 and 4).
•ConnectDrain/Shieldasshown.DonotconnecttoGround(Earth)orWallstation/Control
Interfaces. Connect the bare drain wires and cut off the outside shield.
IEC PELV/NEC® Class 2 Terminal Connections
4 3 2 1
IEC PELV/NEC® Class 2
Power wiring:
1: Common
2: 24 V Power
(2) 18 AWG (1.0 mm
2
) pigtails,
6 in (152 mm) maximum length
D: Drain/Shield
(2) 12 AWG
(2.5 mm
2
)
(2) 12 AWG
(2.5 mm
2
)
Data Link: (1) shielded, twisted
pair 18 AWG (1.0 mm
2
)
4: MUX
3: MUX
Note: 12 AWG (2.5 mm
2
) conductors
for Common (terminal 1) and
24 V Power (terminal 2) will not fit
in terminals; use 18 AWG (1.0 mm
2
)
pigtails (< 6 in/152 mm).
Note: Do not connect Drain/Shield to
Ground (Earth) or Wallstation/Control
Interfaces. Connect the bare drain
wires and cut off the outside shield.
Use Lutron Cable
GRX-CBL-46L
5