SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive PowPak Relay Module with Softswitch Wireless Lighting Control
3691046-04g 1 04.24.19
Vive PowPak Relay Module with Softswitch
The PowPak Relay Module with Softswitch is a radio-frequency
(RF) device that uses Lutron patented Softswitch technology to
control general-purpose loads based on input from Pico remote
controls and Radio Powr Savr occupancy and daylight sensors.
Communication with RF input devices, such as Pico remote
controls and Radio Powr Savr sensors, is accomplished using
Lutron Clear Connect RF Technology.
These products are also compatible with the Vive hub which
enables a simple setup process using a standard web browser
on any Wi-Fi enabled phone, tablet or computer. It also enables
control and monitoring of all Vive devices. The Vive hub can be
added at any time. System reprogramming will be required. For
a complete list of features supported with the Vive hub, see
specification submittal 3691044-04 at www.lutron.com
Note for Replacement: RMMS- the “S” model can replace the
non-”S” model.
Features
Softswitch: Lutron patented technology prevents arcing of relay
contacts, extending product lifetime
Various operating voltages availablerefer to the model
number chart below for details on voltage requirements
Capable of switching general-purpose loads
Receives wireless inputs from up to 10 Pico remote controls,
10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio
Powr Savr daylight sensor
Utilizes Lutron Clear Connect RF Technologyrefer to model
number chart below for frequency band data
Mounts to the exterior of a 100 mm x 100 mm square junction
box through a 20 mm knockout
RMMS-16R-DV-B model shown
Description Model Number Region Operating
Voltage
Frequency Band
PowPak Relay Module with Softswitch
RMMS-16R-DV-B China 220–240 V~ 868.125868.475 MHz
NOTE: Contact Lutron for frequency band compatibility for your geographic region if it is not indicated above.
Model Numbers
1
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive PowPak Relay Module with Softswitch Wireless Lighting Control
3691046-04g 2 04.24.19
Specifications
Power
Operating voltage: 220–240 V~ 50/60 Hz
Standby Power Consumption < 1.0 W
System Communication
Operates using Clear Connect RF Technology for
reliable wireless communication; refer to the model
number chart on page 1 for band frequency details
Wireless sensors and controls must be located within
9 m of the associated control module.
Mounting
This device can be installed on a junction box through
a 20 mm knockout or with mounting screws. The
device must NOT be mounted inside a metallic
enclosure. Improper installation can result in degraded
wireless communications and intermittent or sustained
communications failures and will not be covered under
warranty. Refer to the installation instructions and
consult local and national electric codes for proper
installation.
The PowPak should be installed in an accessible
location and in a way that avoids exposure to high
voltage, particularly in those installations where button
programming is used. Record where it is mounted so
that it can be easily located later.
Metal Ceiling Mounting
Metal ceiling grids must have a > 3 mm gap of
non-metal material which extends the entire length of
the tile on at least one edge. This is often achieved
by foam spacers that are used to prevent tile-to-tile
rattling.
Metal ceiling grids which are continuous (with no
gap) or those that are interlocked, must have a total
surface area that is less than 81 m
2
for each section.
The overall space can be larger as long as there are
non-metal sections bordering or intersecting the metal
sections.
Environment
Ambient operating temperature: 0 °C to 55 °C
0% to 90% humidity, non-condensing
For indoor use only
All drivers and ballasts used with Vive wireless controls
must comply with EN 55015 / CISPR 15
Output Ratings
16 A
No minimum load requirements.
Load types include (but are not limited to):
Incandescent, MLV, ELV, Resistive, Inductive,
Magnetic fluorescent, Electronic fluorescent
Motor rating: 6 A 220 –240 V~
Softswitch
Patented Softswitch circuit eliminates relay arcing at
mechanical contacts
Extends relay life to an average of 1 million cycles
Output is non-latching
Key Design Features
LED status indicator shows current load status and
provides programming feedback
Power failure memory: If power is interrupted,
connected loads will return to the previous level prior
to interruption
NOTICE: Improper installation can result in
degraded wireless communication and/or
intermittent or sustained communication failures,
and will not be covered under warranty.
2
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive PowPak Relay Module with Softswitch Wireless Lighting Control
3691046-04g 3 04.24.19
Dimensions
Dimensions are shown as: mm
Range Diagrams
9 m
Maximum
12 m
9 m
PowPak
Relay Module
Install in center of room to
maximize RF coverage.
Pico Remote
Control
Radio Powr Savr
Occupancy Sensor
20 mm trade size knockout
opening
100
87
72 32
Adaptor
112
NOTE: Wireless sensors and controls must be located within
9 m of the associated control module.
Metal ceiling grids must have a > 3 mm gap of non-metal
material which extends the entire length of the tile on at least
one edge. This is often achieved by foam spacers that are used
to prevent tile-to-tile rattling.
Metal ceiling grids which are continuous (with no gap) or those
that are interlocked, must have a total surface area that is less
than 81 m
2
for each section. The overall space can be larger as
long as there are non-metal sections bordering or intersecting
the metal sections.
3
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive PowPak Relay Module with Softswitch Wireless Lighting Control
3691046-04g 4 04.24.19
System Diagram
Radio Powr Savr Occupancy Sensor (up to 10)
Radio Powr Savr Daylight Sensor (up to 1)
Pico Remote Control (up to 10)
To power source
and load
Wiring Diagram
Line/Hot (L)
Neutral (N)
Switched Line/Hot
Junction Box*
Load
)Lutron, Lutron, Clear Connect, Radio Powr Savr, Pico, PowPak, Softswitch, and Vive are trademarks or registered trademarks of
Lutron Electronics Co., Inc. in the US and/or other countries.
20 mm trade-size knockout opening
Adaptor
* NOTE: The control module mounts to the exterior of a junction box. Do not mount inside a metallic enclosure.
4