SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Power Module with EcoSystemR LQSE-2ECO-D EcoSystemR Controller
369611b 2 10.22.13
Specifications
Power
• 120 V~ 50/60 Hz 120 mA
• 230 V~ 50/60 Hz 80 mA
• Lightning strike protection meets ANSI/IEEE standard
62.31-1980. Can withstand voltage surges of up to
6000V~ and current surges of up to 3000 A.
• Stand by power: 7 W
• BTUs / hour when fully loaded: 24
• EcoSystemR Loop Output: 16 V- 250 mA maximum
per loop.
Standards
• UL
• CE
• Lutron Quality Systems registered to ISO 9001.2008.
• C-Tick S
• cUL
• NOM
Environment
• Surrounding Air Temperature Range: 0 ºC to 65 ºC
(32 ºF to 149 ºF).
• Relative humidity: less than 90% non-condensing.
• Calibration point maximum: 75 ºC (167 ºF)
• For indoor use only.
Terminals
• Mains wiring: 1.0 mm
2
to 4.0 mm
2
(18 AWG to 12AWG)
• EcoSystemR
Loop Wiring: 1,0 mm
2
to 4,0 mm
2
(18 AWG to 12AWG)
• QS Wiring: 1,0 mm
2
(18AWG)
• Minimum wire temperature rating = 65 °C (149 ºF),
Cu only
Mounting
• Intended to mount within an IP20 (minimum) rated
consumer panel or breaker panel with integrated DIN
rail and dead cover
• Width = 9 DIN modules (161.7 mm or 6
3
⁄8 in).
Programming and Compatibility Requirements
• The LQSE-2ECO-D can only be used with the
HomeWorksRQS system.
• Setup and programming of the Power Module with
EcoSystemR is done through the HomeWorksRQS
programming software.
EcoSystemR
• Control up to 64 EcoSystemR-compatible devices
(ballast or LED drivers) per EcoSystemR Digital Loop (up
to 128devices per Power Module with EcoSystemR unit).
• Digitally define areas and zones.
•
Automatic replacement of a single failed ballast or driver.
• Simple method of replacing multiple failed ballasts
or drivers.
•
EcoSystemR Digital Loop can be wired as Mains voltage
or IEC PELV / NECR Class 2 for maximum wiring flexibility.
• EcoSystem® Loop wires are polarity insensitive and
topology-free.
EcoSystemR Digital Loop Limits
• Up to 64 EcoSystemR-compatible fluorescent ballasts
and/or LED drivers per EcoSystemR digital loop.
• EcoSystemR-compatible fluorescent ballasts and LED
drivers on the EcoSystemR digital loop do not count as
QS devices.
QS Link Limits
• A QS link in a HomeWorks
®QS system can have up
to 512 zones (outputs) and 100devices. A ballast or
driver counts as 1 zone unless specifically grouped
into zones from the HomeWorks
®QS software.
• Each Power Module with EcoSystemR unit counts as
one device toward the 100 device limit.
• A maximum of 8 fully loaded EcoSystemR digital loops
may be connected to a single QS link.
HomeWorksR QS Wallstations
• HomeWorksR QS wallstations can be configured to
control Power Module with EcoSystemR units with the
HomeWorksR QS programming utility.
• LED indicator displays the status of programmed lights.
Troubleshooting and Maintenance
Features
• Maintains redundant memory of ballast programming
for ease of single or multiple ballast replacement.
• To verify EcoSystem
® lights connected to EcoSystemR
Loop 1 and Loop 2:
– Enter Test Mode: Press and hold Test button on
the Power Module with EcoSystemR until the Test
LED starts flashing.
– Test: Each press of either the ECO 1 or ECO 2
button will cycle the lights between high-end,
low-end, flash, and off for that loop.
– Exit Test Mode: Press and hold Test button
until Test LED stops flashing.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts