SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem® 5-Series LED Driver for Japan 5% Dimming
369754b 2 05.13.14
Specifications
Performance
• Dimming Range: 100% to 5%
1
• Dimming method: constant-current reduction,
refer to LutronR application note #360 for details
• Operating Voltage: 100 or 200 V~
at 50/60 Hz
• Patented thermal foldback protection
• LED lighting turns on to any dimmed level without
flashing to full brightness
• Turn on time: < 100 ms typical from electronic off
• Non-volatile memory restores all driver settings after
power failure
• Power Factor: λ > 0.95 at maximum power
• Meets Harmonics requirements for IEC-61000-3-2
• Output open circuit protected
• Output short circuit and overload protected
• Lifetime: 50 000 hours at:
t
c
= 60 °C 35 W
t
c
= 65 °C 25 W, 18 W, 15 W
Measured at t
a
= 40 °C
2
• Typical standby power consumption 0.5 W
Environmental
• Sound Rating: Inaudible in 24 dB ambient
• Relative Humidity: maximum 90% non-condensing
• Operating Range: t
a
= 0 to 40 °C
2
• Maximum case temperature:
t
c
= 60 °C at 35 W maximum power
t
c
= 65 °C at 25 W, 18 W, and 15 W maximum power
Regulatory Approvals and Compliance
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20
• LutronR Quality Systems registered to ISO
9001.2008
• PSE Compliant
Driver Wiring & Mounting
• Wiring Method: daisy chain capable terminals for
input and EcoSystemR signal terminals
• Daisy Chain Line / Neutral maximum
– 100 V~: 25 drivers maximum
– 200 V~: 50 drivers maximum
• Mains wire size ( ): 1.6 - 2.0 mm (solid wire only)
• EcoSystemR signal wire size ( ): 0.8 - 1.2 mm (solid
or stranded wire)
• Output (LED) wire: 0.5 mm
2
to 0.75 mm
2
• Install in compliance with local electric codes
• Provide adequate space to ensure convective
cooling of LED driver. Remove any insulation or heat
generating equipment or obstruction within 150 mm
of LED driver.
Circuit Breaker Information
• Maximum number of drivers on Fuji Electric
F53C-BF2BC-020 or similar circuit breaker:
– 100 V~ : 25 drivers maximum
– 200 V~ : 50 drivers maximum
OEM Notes
• For best dimming performance, Lutron
recommends insulation with 50 / 60 Hz impedance
of at least 12 MΩ and minimum breakdown voltage
of at least 1 500 V~ between LEDs and fixture
chassis.
EcoSystem®
5-Series LED
5%
調光
LED
ドライバー
t
c
E1
E2
V VF
1.6 – 2.0 mm
LN
CPEVS
0.8-1.2 mm
-V
黒赤
出力
+V
電源入力
信号入力
適合するLED負荷のみ
接続可能
•
•
•
•
•
EcoSystem
®
LED
ドライバ-
•
•
•
-V
+V
2次側配線長 最大15m
E2
E1
N
L
lutron.jp
0120-083-417
2 5 W
: 1.05 A
出力
LDE52D1JTN-MA105
9 999999 999987
•
t
c
1
Light output at 5% depends on the efficacy of the light engine used with the driver.
2
Where t
a
is the temperature of the air directly surrounding the driver
