Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver 1% Dimming
369832p 2 08.21.19
Specifications
Regulatory Approvals and Compliance
• UL® Listed Class P
• NOM certified for Mexico (only “BLK” models for use
with Lutron QwikFig technology)
• Lutron Quality Systems registered to ISO 9001.2015
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20
• Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV
• Inrush current less than NEMA 410-2011 limit
• FCC Part 15 Class A
• Canadian EMI Class A Compliance Equivalent:
CAN ICES-005(A)/NMB-005(A)
• Meets UL 8750, “Light Emitting Diode (LED)
Equipment For Use in Lighting Products”
• Class 2 output
• LED drivers need to meet certain performance criteria
in order for the completed luminaires to comply with
the ENERGY STARR Luminaires V2.0 Specification. All
models meet these performance criteria throughout their
entire load compatibility regions. Consult Application
Note #599 (P/N 048599), ENERGY STAR® Luminaires
V2.0 and Lutron Drivers, at www.lutron.com for
availability dates of compliant products
• LED drivers need to meet certain performance criteria
in order for the completed luminaires to comply with
Title 24 requirements as detailed in CEC-400-2015-
037-CMF. All models meet both commercial
(at 120 V~ / 277 V~) and residential (at 120 V~)
performance criteria throughout their entire load
operating regions. Consult CEC-400-2015-032-CMF
Section 6.2.7 for important information on meeting
start-up time requirements with fade-in lighting.
• M-case type performance is in compliance with
DLC version 2.1 in designated areas (see “Load
Compatibility” graph in Output Range pages)
Performance
• Soft-on, Fade-to-Black: fades smoothly between
0% and 1% when turned on and off for an
incandescent-like experience
• Dimming Range: 100% to 1%
1
• Operating Voltage: 120 V~ to 277 V~ at 50 / 60 Hz
• Lifetime: 50,000 hours when calibration point (t
c
) at
75°C (167 °F)
2
• For rated warranty, t
c
not to exceed 75 °C (167 °F)
(maximum rated temperature)
2
• Patented thermal foldback protection
• At turn on, lighting fades smoothly to the desired level
without decreasing or flashing to full brightness
• Non-volatile memory restores all driver settings after
power failure
• Typical standby power consumption: 0.2 W at 120 V~
and 0.3 W at 277 V~
• Open-circuit protected output
• Short-circuit and overload-protected output
• Class 2 output designed to withstand hot swap of the
LED load
Environmental
• Sound rated: Class A inaudible in 24 dBA ambient
• Relative Humidity: maximum 90% non-condensing
• Minimum Operating Ambient Temperature:
t
a
= 0 °C (32 °F)
3
• Indoor use only
• Rated for dry and damp locations
Driver Wiring and Mounting
• Driver is grounded by a mounting screw to the
grounded fixture or by terminal connection
• Terminal blocks on the driver accept one solid
wire per terminal from 18 AWG to 16 AWG (0.75 mm
2
to 1.5 mm
2
)
• Fixture must be grounded in accordance with local
and national electrical codes
• Maximum driver-to-LED light engine wire length for:
Wire Gauge
Maximum Lead Length
150 mA to
700 mA
710 mA to
1.50 A
1.51 A to
2.10 A
18 AWG (0.75mm
2
) 30 ft (9 m) 15 ft (4.5 m) 10 ft (3 m)
16 AWG (1.5mm
2
) 35 ft (10.5 m) 25 ft (7.5 m) 15 ft (4.5 m)
14 AWG (2.5mm
2
)
4
50 ft (15 m) 40 ft (12 m) 25 ft (7.5 m)
12 AWG (4.0mm
2
)
4
100 ft (30 m) 60 ft (18 m) 40 ft (12 m)
1
Light output at 1% depends on the efficacy of the LED light engine used
with the driver.
2
To maintain warranty, installer is responsible for ensuring that the driver
calibration point does not exceed 75 ºC (167 ºF).
3
Where t
a
is the temperature of the air directly surrounding the driver.
4
Terminal blocks on the drivers accept only solid 18 AWG to 16 AWG
(0.75 mm
2
to 1.5 mm
2
) wire. To use wire gauges larger than the terminal
blocks’ rated gauge of 16 AWG (1.5 mm
2
) refer to the Terminal Wiring
Gauges diagram. Connect up to 3 ft (1.0 m) of 18 AWG to 16 AWG
(0.75 mm
2
to 1.5 mm
2
) wire to the LED driver terminal blocks, then
connect 12 AWG or 14 AWG (4.0 mm
2
or 2.5 mm
2
) up to the length
allowed in the above table.