5-Series EcoSystem LED Driver
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver 5% Dimming
369823o 2 08.21.19
Specifications
Regulatory Approvals and Compliance
• UL® Listed Class P
• NOM certified for Mexico (only “BLK” models for use
with Lutron QwikFig technology)
• Lutron Quality Systems registered to ISO 9001.2015
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20
• Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV
• Inrush current less than NEMA 410-2011 limit
• FCC Part 15 Class A
• Canadian EMI Class A Compliance Equivalent:
CAN ICES-005(A)/NMB-005(A)
• Meets UL 8750, “Light Emitting Diode (LED)
Equipment For Use in Lighting Products”
• Class 2 output
• LED drivers need to meet certain performance criteria
in order for the completed luminaires to comply with
the ENERGY STAR® Luminaires V2.0 Specification. All
models meet these performance criteria throughout
their entire load compatibility regions.
Consult Application Note #599 (P/N 048599),
ENERGY STARR Luminaires V2.0 and Lutron
Drivers, at www.lutron.com for availability dates of
compliant products
• LED drivers need to meet certain performance criteria
in order for the completed luminaires to comply with
Title 24 requirements as detailed in CEC-400-2015-
037-CMF. All models meet both commercial
(at 120 V~ / 277 V~) and residential (at 120 V~)
performance criteria throughout their entire load
operating regions. Consult CEC-400-2015-032-CMF
Section 6.2.7 for important information on meeting
start-up time requirements with fade-in lighting.
• M-case type performance is in compliance with
DLC version 2.1 in designated areas (see “Load
Compatibility” graph in Output Range pages)
Performance
• Dimming Range: 100% to 5%
1
• Operating Voltage: 120 V~ to 277 V~ at 50 / 60 Hz
• Lifetime: 50,000 hours when calibration point (t
c
) at
75°C (167 °F)
2
• For rated warranty, t
c
not to exceed 75 °C (167 °F)
(maximum rated temperature)
2
• Patented thermal foldback protection
• At turn on, lighting fades smoothly to the desired level
without decreasing or flashing to full brightness
• Non-volatile memory restores all driver settings after
power failure
• Typical standby power consumption: 0.2 W at 120 V~
and 0.3 W at 277 V~
• Open-circuit protected output
• Short-circuit and overload-protected output
• Class 2 output designed to withstand hot swap of the
LED load
• Device turn-on time: <100 ms from electronic off and
< 500 ms from power off
• Dimming method: Constant-current reduction, refer to
Lutron Application Note #360 (P/N 048360) at
www.lutron.com for details
Environmental
• Sound rated: Class A inaudible in 24 dBA ambient
• Relative Humidity: maximum 90% non-condensing
• Minimum Operating Ambient Temperature:
t
a
= 0 °C (32 °F)
3
• Indoor use only
• Rated for dry and damp locations
Driver Wiring and Mounting
• Driver is grounded by a mounting screw to the
grounded fixture or by terminal connection
• Terminal blocks on the driver accept one solid wire per
terminal from 18 AWG to 16 AWG (0.75 mm
2
to 1.5 mm
2
)
• Fixture must be grounded in accordance with local
and national electrical codes
• Maximum driver-to-LED light engine wire length for:
Wire Gauge
Maximum Lead Length
150 mA to
700 mA
710 mA to
1.50 A
1.51 A to
2.10 A
18 AWG (0.75mm
2
) 30 ft (9 m) 15 ft (4.5 m) 10 ft (3 m)
16 AWG (1.5mm
2
) 35 ft (10.5 m) 25 ft (7.5 m) 15 ft (4.5 m)
14 AWG (2.5mm
2
)
4
50 ft (15 m) 40 ft (12 m) 25 ft (7.5 m)
12 AWG (4.0mm
2
)
4
100 ft (30 m) 60 ft (18 m) 40 ft (12 m)
1
Light output at 5% depends on the efficacy of the LED light engine used
with the driver.
2
To maintain warranty, installer is responsible for ensuring that the driver
calibration point does not exceed 75 ºC (167 ºF).
3
Where t
a
is the temperature of the air directly surrounding the driver.
4
Terminal blocks on the drivers accept only solid 18 AWG to 16 AWG
(0.75 mm
2
to 1.5 mm
2
) wire. To use wire gauges larger than the terminal
blocks’ rated gauge of 16 AWG (1.5 mm
2
) refer to the Terminal Wiring
Gauges diagram. Connect up to 3 ft (1.0 m) of 18 AWG to 16 AWG
(0.75 mm
2
to 1.5 mm
2
) wire to the LED driver terminal blocks, then
connect 12 AWG or 14 AWG (4.0 mm
2
or 2.5 mm
2
) up to the length
allowed in the above table.