Fillable 369753 ENG EcoSystem 5 Series LED Driver Overview Spec (369753)

Fill Online, Printable, Fillable, Blank 369753 ENG EcoSystem 5 Series LED Driver Overview Spec (369753) Form

Use Fill to complete blank online LUTRON ELECTRONICS, INC. pdf forms for free. Once completed you can sign your fillable form or send for signing. All forms are printable and downloadable.

369753 ENG EcoSystem 5 Series LED Driver Overview Spec (369753)

On average this form takes 16 minutes to complete

The 369753 ENG EcoSystem 5 Series LED Driver Overview Spec (369753) form is 9 pages long and contains:

  • 0 signatures
  • 0 check-boxes
  • 63 other fields

Country of origin: US
File type: PDF

Use our library of forms to quickly fill and sign your Lutron Electronics, Inc. forms online.

BROWSE LUTRON ELECTRONICS, INC. FORMS

Related forms
Fill has a huge library of thousands of forms all set up to be filled in easily and signed.
Fill in your chosen form
Sign the form using our drawing tool
Send to someone else to fill in and sign.
find another form
 
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 1 05.08.19
EcoSystem 5-Series LED Driver
(220–240 V~, CE)
EcoSystem 5-Series LED Drivers provide a high
performance solution for any space in any
application, while providing smooth, continuous
dimming down to 5% of output current.
Features
• Continuous, flicker-free dimming from 100% to 5%
1
• Guaranteed dimming performance when used with
Lutron controls
• Compatible with Energi Savr Node EcoSystem
and Energi Savr Node DALI® units, GRAFIK Eye
QS control unit with EcoSystem, PowPak dimming
module with EcoSystem, Quantum systems and
HomeWorks QS systems, allowing for integration
into a planned or existing EcoSystem lighting
control solution
• Protected from miswires of input power to
EcoSystem control inputs
• CE compliant and ENEC certified
• Independent control gear with integral strain relief
• SELV output
• A rated lifetime of 50 000 hours at 40 °C ambient
• 100% performance tested at factory
• RoHS compliant
• Non-volatile memory restores all settings after
power failure
• Constant-current reduction dimming
• For more information please visit:
www.lutron.com/5SeriesLED
EcoSystem LED Driver
53,7 mm W x 30,8 mm H x 215,0 mm L
1
Light output at 5% depends on the efficacy of the light engine used with the driver.
Neutral
Primary
NLE1 E2
N/C
Digital Bus
N/C N/C
-V +V
SELV Secondary
EcoSystem®
LED Driver
lutron.com
EcoSystem
®
5-Series LED
5% Dimming LED Driver
+44.
(
0
)
20.7680.4481
•
•
•
•
-V
+V
9 999999 999987
LDE53E1CRN-RA070
t
c
15,0 m (50 ft) Max
Line
E1
E2
N/C
LED
Load
Only
SEC: 700 mA
35 W
1
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 2 05.08.19
Specifications
Performance
• Dimming Range: 100% to 5%
1
• Dimming method: constant-current reduction
Refer to Lutron application note #360 (048360), at
www.lutron.com for details
• Operating Voltage: 220–240 V~ 50/60 Hz
• Lifetime: 50 000 hours at:
t
c
= 75 °C 36 W, 35 W, 25 W
t
c
= 65 °C 18 W, 15 W, 13 W
Measured at t
a
= 40 °C
2
• Patented thermal foldback protection
• LED lighting turns on to any dimmed level without
flashing to full brightness
• Non-volatile memory restores all driver settings after
power failure
• Power Factor:
λ > 0,95 at 25 W, 35 W, and 36 W maximum power
λ > 0,93 at 15 W maximum power
λ > 0,91 at 13 W maximum power
• Typical standby power consumption: 0,5 W
• Meets Harmonics requirements for IEC-61000-3-2
• Output open circuit protected
• Output short circuit and overload protected
• Turn-on time: < 100 ms typical from electronic off
Environmental
• Sound rated: inaudible in 24 dB ambient
• Relative Humidity: maximum 90% non-condensing
• Operation Range: t
a
= 0 to 50 °C
2
• Maximum case temperature:
t
c
= 85 °C at 25 W, 35 W, and 36 W maximum power
t
c
= 75 °C at 13 W, 15 W, and 18 W maximum power
Regulatory Approvals
• CE compliant and ENEC certified
– Safety: IEC/EN 61347-2-13
– Emissions: CISPR15/EN55015, IEC 61000-3-2, 3-3
– Immunity: IEC/EN 61547,
IEC/EN 61000-4-2, -4-3, -4-4, -4-6, -4-11
– Performance: IEC/EN 62384
• RoHS 2006 Compliant
• IEC 60529, IP20 Rating
• DALI® Compliant
• Compliant with IEC62386-207
• Lutron Quality Systems registered to ISO 9001.2015
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20.
Neutral
Primary
NLE1 E2
N/C
Digital Bus
N/C N/C
-V +V
SELV Secondary
EcoSystem®
LED Driver
lutron.com
EcoSystem® 5-Series LED
5% Dimming LED Driver
+44.
(
0
)
20.7680.4481
•
•
•
•
-V
+V
9 999999 999987
LDE53E1CRN-RA070
t
c
15,0 m (50 ft) Max
Line
E1
E2
N/C
LED
Load
Only
SEC: 700 mA
35 W
•
t
c
1
Light output at 5% depends on the efficacy of the light engine used with the driver.
2
Where t
a
is the temperature of the air directly surrounding the driver.
2
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 3 05.08.19
Driver Wiring & Mounting
• Wiring Method: daisy chain capable terminals for input
• Torque range on terminal screws: 0,45 to 0,5 N•m
• Torque range on strain relief screws: 0,5 to 0,8 N•m
• Power Input Terminals:
– Daisy chain capable wire size: 0,75 mm
2
to 2,5 mm
2
(18 AWG to 14 AWG)
– Daisy chain, Line / Hot, and Neutral Maximum:
20units
1
− Second pair of terminals provided to daisy chain
Line / Hot and Neutral
– When placing multiple wires in the same strain relief,
all wire diameters must be the same
• EcoSystem Terminals:
– Daisy chain capable (2 cable per terminal) wire size:
0,75 mm
2
to 1,5 mm
2
(18 AWG to 16 AWG)
– Not daisy chain capable (1 cable per terminal) wire
size: 1,75 mm
2
to 2,5 mm
2
(14 AWG)
– When placing multiple wires in the same strain relief,
all wire diameters must be the same
• Output Terminals:
– Wire size: 0,75 mm
2
to 1,5 mm
2
(18 AWG to 16 AWG)
• Maximum lamp-to-driver wire length is 15 m using
0,75 mm
2
to 1,5 mm
2
(18 AWG to 16 AWG) wire.
• Maximum Number of Drivers on Miniature Circuit
Breaker:
– 16 A Type B: 20 drivers
– 16 A Type C: 34 drivers
• Provide adequate space to ensure convective
cooling of LED driver. Remove any insulation or heat
generating equipment or obstruction within 150 mm of
LED driver.
N ote: Ground termination not provided. Terminate
ground in compliance with local electric codes.
OEM Notes
• For best dimming performance, Lutron recommends
electrical insulation with 50 / 60 Hz impedance of at
least 12 MΩ and minimum breakdown voltage of at
least 1 500 V~ between LEDs and fixture chassis.
1
Subject to wire size limitations. See Power Wiring Diagram page for wiring diagrams.
3
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 4 05.08.19
Model Numbers:
Model Number Maximum Power
Rated Output
Current
Compatible Load Voltage Range at
Rated Output Current
Typical Efficiency at
Maximum Power
LDE53E1CRN-RA070 20 to 35 W 0,700 A 27,7 to 50,0 V 87%
LDE53E1CRN-TA090 25 to 36 W 0,900 A 27,7 to 40 V 86%
LDE53E1CRN-JA105 20 to 35 W 1,050 A 18,8 to 33,3 V 86%
LDE53E1CRN-LA140 18 to 35 W 1,400 A 12,9 to 25,0 V 86%
LDE52E1CRN-PA050 12 to 25 W 0,500 A 24,0 to 50,0 V 85%
LDE52E1CRN-FA070 12 to 25 W 0,700 A 16,4 to 35,7 V 84%
LDE52E1CRN-MA105 7 to 25 W 1,050 A 6,6 to 23,8 V 84%
LDE52E1CRN-KA140 13 to 25 W 1,400 A 9,3 to 17,9 V 84%
LDE51E1CRN-GA035 6 to 18 W 0,350 A 17,1 to 51,4 V 83%
LDE51E1CRN-NA050 5 to 15 W 0,500 A 10,0 to 30,0 V 80%
LDE51E1CRN-GA025 6 to 13 W 0,250 A 24,0 to 52,0 V 80%
LDE51E1CRN-QA070 5 to 15 W 0,700 A 7,1 to 21,4 V 80%
4
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 5 05.08.19
Load learning
What is load learning?
Each Lutron constant-current LED driver is able to operate over a range of LED load voltages. In order to operate
with optimum efficiency, these drivers continuously sense the LED load voltage and make adjustments to their
internal operation.
When does load learning happen?
Load learning happens continuously and in most cases is imperceptible. However, when a new load is connected
to the driver it will take some time for the LED driver to adapt. A driver may be performing load learning during
R&D/bench testing, production testing, or QwikFig/AirFig configuration when using a real load. If a driver was not
allowed to learn its load during the fixture production process, it may happen when first installed in the final
location.
What does load learning look like?
Depending on the difference in forward voltage of the new load versus the last load the driver learned, one of the
following may be observed:
1. The load may seem to operate properly.
2. The load may turn on at a low light level and remain there for a few seconds before transitioning to full light.
3. The load may turn on for a very brief flash, then go off for a few seconds before turning back on again.
4. There may be no light output at all for up to 20 seconds.
How do I make a driver “learn” a new load?
Although this process will happen on its own during normal usage, Lutron recommends the following procedure
be carried out before attempting to confirm proper operation:
1. Power up the LED driver on the intended load.
2. Once the light seems to be stable at full output, which may take 20 to 30 seconds, leave the driver on for another
20 seconds for the driver to learn the load voltage and commit it to memory.
Note: There is no limit to the number of times a driver can learn a new load.
5
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 6 05.08.19
Case Dimensions (typical)
A 53,7 mm
B 215,0 mm
C 30,8 mm
D 60,0 mm
E 26,8 mm
F 208,1 mm
Mounting Centers
• Recommended mounting screw: M3,5
D
A
B
E
F
C
6
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 7 05.08.19
EcoSystem LED Driver Wiring Diagrams
EcoSystem Digital Link Overview
• The EcoSystem Digital Link wiring (E1 and E2)
connects the drivers together to form a lighting
control system.
• For EcoSystem link limits, refer to EcoSystem
control specifications.
• E1 and E2 (EcoSystem digital link wires) are polarity
insensitive and can be wired in any topology.
• An Energi Savr Node unit with EcoSystem,
GRAFIK Eye QS control unit with EcoSystem,
PowPak dimming module with EcoSystem, Quantum
system or HomeWorks QS system provides power
for the EcoSystem Digital Link and supports system
programming.
• All EcoSystem Digital Link programming is
completed by using the Energi Savr App for Apple
iPad, iPod Touch or iPhone mobile digital devices,
GRAFIK Eye QS with EcoSystem, PowPak dimming
module with EcoSystem, Quantum system, or
HomeWorks QS system.
EcoSystem Digital Link Wiring
• Driver EcoSystem Digital Link terminals may either
accept one 0,75 mm
2
to 2,5 mm
2
(18 AWG to
14 AWG) solid or stranded copper wire per terminal
or two 0,75 mm
2
to 1,5mm
2
(18 AWG to 16 AWG)
solid or stranded copper wires per terminal.
• Make sure that the mains breaker to the driver and
EcoSystem Digital Link Supply is OFF when wiring.
• Connect the two conductors to the two driver
terminals E1 and E2 as shown.
• To avoid confusion and shorting the link when daisy
chaining several drivers, the use of different color
wires is recommended.
• Consult applicable electrical codes for proper wiring
practices.
Notes
• The EcoSystem Digital Link Supply does not have to
be located at the end of the Digital Link.
• EcoSystem Digital Link length is limited by the wire
gauge used for E1 and E2 as follows:
Wire Size
Digital Link Length
(max)
2,5 mm
2
515 m
1,5 mm
2
310 m
1,0 mm
2
205 m
0,75 mm
2
155 m
14 AWG 1 400 ft
16 AWG 900 ft
18 AWG 550 ft
To other EcoSystem
Digital Link
compatible devices
(for PowPak up to
32 total devices, for
all other EcoSystem
products: up to
64 total devices)
EcoSystem Daisy Chain Wiring
N/C
E1
E2
Digital Bus
N/C
E1
E2
Digital Bus
UNIT 1 UNIT 2
7
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 8 05.08.19
Power Wiring Diagram
Up to 20 EcoSystem Drivers can
have their power input terminals
chained together, while 64 digital
terminals can be chained
Up to 64 total devices on the EcoSystem or DALI® Link.
Up to 32 total devices per EcoSystem Link on the PowPak dimming
module with EcoSystem.
Line/Hot
Neutral
EcoSystem or DALI® Bus
EcoSystem or DALI® Bus
Line/Hot
Line/Hot
NeutralNeutral
EcoSystem
or DALI® Bus
1 2 3 4 20
8
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
LED Dimming Driver EcoSystem 5-Series LED Driver for Europe 5% Dimming
369753e 9 05.08.19
Hi-lume
A-Series
**
Dimmed Hot
Switched Hot
Neutral
Ground
To
3-wire
Dimming
Control
+V
Ground*
-V
†
†
LED
light
engine
Hi-lume
A-Series
**
Dimmed Hot
Neutral
Ground
To ELV
Dimming
Control
+V
Ground*
-V
†
†
LED
light
engine
RED
BLUE
YELLOW
BLUE/WHITE
LAMPS
7 ft Max. lead length
P/N 500-13362 Rev. A
NEU
N/C
SH
B/WB/W BLUBLURED YEL YEL
E1
E2
NEUTRAL
SWITCHED HOT
TO
EcoSystem
® H
BUS
E1
E2
Ecosystem® H
Ballast
C
A
L
I
B
R
A
T
I
O
N
P
O
I
N
T
Coopersburg, PA 18036 USA
RED
Programmed Rapid Start
1% Electronic Fluorescent Dimming
Ballast
CLASS 2
BUS
LINE
®
Solid 18 or 16 AWG
wire for power and bus terminals
18 AWG wire only for lamps.
5/16 in
(8 mm)
1-800-523-9466
Copper wire only
Consult lamp manufacturer for lamp seasoning
requirements prior to dimming.
Warranty void if unit is opened.
WARNING: Shock hazard. May result in serious injury or
death. Disconnect power before servicing or installing.
Calibration point temperature not to exceed 65 °C.
Maximum case temperature 75 °C.
Ecosystem® H
TO LINE
VOLTAGE
SOURCE
Pantone
362
500-13362 Rev. A
Label Size: 6.87” x 2.125”
Corner Radius: 0.0625”
Colors:
Pantone
186
Pantone
1585
Pantone
116
Pantone
3005
Pantone
2583
Pantone
Black
Wiring Diagram for EcoSystem Digital Control
ATTENTION
ELECTRICIANS and CONTRACTORS
Driver Leads
Lead lengths from driver to LED light engine must not
exceed 15 m.
Wiring
Drivers must be installed per national and local
electrical codes.
Provide adequate space to ensure convective cooling
of LED driver. Remove any insulation or heat generating
equipment or obstruction within 150 mm of LED driver.
Maximum Operating Temperature:
Drivers must not exceed the rated calibration point
temperature (t
c
).
ATTENTION
FACILITIES MANAGERS
SERVICE
Warranty
For warranty information, please see
www.lutron.com/ballastdriverwarranty
Replacement Parts
Use replacement parts with exact Lutron model
numbers. Consult Lutron if you have any questions.
Contact Information
For further information, please visit us at
www.lutron.com/europe or contact Lutron
Customer Assistance at
+44.(0)20.7680.4481 (Europe)
+1.610.282.3800 (USA Headquarters)
Please provide exact model number when calling.
* Maximum lamp-to-driver wire length is 15 m using 0,75 mm
2
to 1,50 mm
2
(18 AWG to 16 AWG) wire.
Neutral
EcoSystem
5-Series
LED Driver
V+ * (Red)
LED
light
engine
V- * (Black)
To Mains
To
EcoSystem
digital link
Line / Hot
E1
E2
Wire Size: mm
2
(AWG)
Model Number
Driver
Rating
(A)
0,5
(20)
0,75
(18)
1,0
(16)
1,5
(14)
LDE53E1CRN-LA140
LDE52E1CRN-KA140
1,40 4 6 8 11
Maximum
Wire Length
(m)
LDE53E1CRN-JA105
LDE52E1CRN-MA105
1,05 7 10 13 15
LDE53E1CRN-TA090 0,9 9 14 15 15
LDE53E1CRN-RA070
LDE52E1CRN-FA070
LDE51E1CRN-QA070
0,70 15 15 15 15
LDE52E1CRN-PA050
LDE51E1CRN-NA050
0,50 15 15 15 15
LDE51E1CRN-GA035 0,35 15 15 15 15
LDE51E1CRN-GA025 0,25 15 15 15 15
)Lutron, Lutron, EcoSystem, Energi Savr Node, GRAFIK Eye,
HomeWorks, PowPak, and Quantum are trademarks or registered
trademarks of Lutron Electronics Co., Inc. in the U.S. and other countries.
Apple, iPad, iPod Touch, and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
DALI is a registered trademark of ZVEI - Zentralverband Elektrotechnik-
undElektronikindustrie e.V.
9
Download
Save PDF to desktop
Email
Email completed PDF
Send for Signing
Email for others to sign
Print
Print document
Choose a Field
Click on a field and
select the person that should complete it
Want to add a signature?
You can add a signature field
and assign it to someone else
to sign
Choose a Field
Click on a field and
select the person that should complete it

369753 ENG EcoSystem 5 Series LED Driver Overview Spec (369753)

This document is locked as it has been sent for signing.

You have successfully completed this document.

Other parties need to complete fields in the document. You will recieve an email notification when the document has been completed by all parties.

This document has been signed by all parties.

Completed 30 April 2020

Message

View Audit Log
Print With Audit Log
Duplicate Document