SOLID FUEL BURNER CHECKLIST/PROCESSING SHEET
To be filled out in full for all solid fuel burner building consent applications
.
Address of installation: ________________________________
__________________
Heater make and model: ________________________________
_________________
OFFICE USE ONLY
Application complete and accepted by vetting officer:
Name:
Signed: Accept More Info N/A
Date:
Building Category:
Two copies of specification, installation requirements and floor plan provided.
Free Standing
Inbuilt
Wood
Multi Fuel
Open Fire
Pellet
Second Hand Heater Provide a letter from an Approved Person confirming the
heater is acceptable to install. An Approved Person could be on Councils Producer
Statement Register or be approved by the heater manufacturer. Note: Heater must
have a new flue system
Manufacturer’s Installation information supplied (Heater is tested to and complies
with AS/NZS 2918:2001)
Heater installation requires heat shielding as it does not meet the clearance
requirements of the Manufacturer’s instructions or AS/NZS 2918:2001. Provide
reduction factor calculation page of AS/NZS 2918:2001 and indicate reduced
clearances on floor plan
Building consent number:
Accept More Info N/A
Comments:
SBCG 19SF – V3 23/01/15
Page 1 of 3
Clean air requirements: Does the heater comply with any applicable Regional
Authority/MFE emission standards?
Yes
No
N/A
Authorisation number (If applicable) ___________________
Accept More Info N/A
Comments
Flue and liner system:Manufacturer’s technical information supplied
Skillion Roof: if dwelling has a skillion roof, provide construction detail of flue
penetration.
If a flue offset is required, provide a dimensioned drawing of the offset & detail
where the offset is located (e.g. in the roof space, in the room)
Roof flashing information provided to comply with NZBC E2 e.g.
Dektite, Tray
flashing etc.
Circle number of floors the flue penetrates: 0 1 2 Other: ____
If the flue penetrates 1 or more floors, please provide a construction detail of the
penetration.
Chimney ventilation information provided.
Accept More Info N/A
Comments
Heater fitted with Wetback:
Connected to open vented HWC to comply with NZBC G12/AS1
Yes
Tempering valve being fitted.
Yes
No
Existing
Name of Certifying Plumber. _______________________
Drawing provided of wetback revolve pipe setup.
Accept More Info N/A
Comments
Drapes/Curtains:
Has consideration been given to the proximity of window drapes/curtains/
coverings? These are to be restrained to maintain the minimum clearances for heat
sensitive materials.
Accept More Info N/A
Comments
NZBC F7 Warning Systems: Smoke alarms shall be located as follows:
a. In multi-storey units, there shall be at least one smoke alarm on each level within
the household unit.
b. On levels containing sleeping spaces, the smoke alarms shall be located either:
i) In every sleeping space, or
ii) Within 3.0m of every sleeping space door. In this case, the smoke alarms must
be audible to sleeping occupants on the other side of the closed doors.
c. In all cases, so the sound pressure level complies with that specified in NZS 4514.
Comment: Smoke alarms also need to be located so that an alarm is given before the escape route from
any bedroom becomes blocked by smoke. This includes those parts of escape routes on other floors.
Although not required by this Acceptable Solution, the interconnection of individual smoke alarms should be
considered if audibility is a problem.
Smoke alarms as per above in the dwelling are shown on floor plan.
Accept More Info N/A
Comments
SBCG 19SF V3 – 23/01/15 Page 2 of 3
Office use only
Further Information Requested / Phone Call / Counter advice:
Date
Name
Time cost
Date provided
Date approved
Granting of Building Consent
Na
me of building control officer:
Si
gned: Date:
I am
competent to undertake processing on this building consent and am
satisfied on reasonable grounds that the provisions of the building code will
be met if the building work is completed in accordance with the plans and
specifications contained in this building consent (as per Section 49 of the
Building Act 2004). I hereby grant this consent subject to payment of
outstanding fees.
Senior review (optional)
Name of senior building control officer:
Si
gned: Date:
I have undertaken a review of the processing of this building consent and am
satisfied on reasonable grounds that the processing officer has undertaken a
competent check in accordance with the processing sheet and the
requirements of the building code.
SBCG 19SF V3 – 23/01/15 Page 3 of 3
click to sign
signature
click to edit
click to sign
signature
click to edit