Residential Permit Application and Submittal Requirements
The following sections located on page one must be completed in full :
I. County and Municipality
2. Location of proposed work or improvement, most importantly, site location, tax parcel number and lot number.
3. Type of improvement including a brief description of work.
4. Owner information with complete mailing address.
5. Estimated cost of construction is required to be provided.
The contactor section is required to be completed only
when work is performed within Municipalities that require contractor registration. However,
Code
Inspections, Inc. requests a minimum of the primary contractor information to be provided in case correspondence or contact is
necessary.
Page two needs to be completed for only the sections that apply to the proposed project, or work to be
performed.
Page three needs to be completed for floodplain information and, a signature by the property owner, or agent of the owner must be provided on
page
three. The bottom of page three is intended for administrative use and will be completed by Code Inspections, lnc. during the application
review.
PLANS AND
SUBMITTALS
• The submittal shall include one complete set of plans, a plot plan and specification sufficient to indicate the scope of work being proposed. Listed
below
are some basic examples of information necessary to complete a plan review. Additional information may be requested depending on
the
intended project. Any document larger than 11 x 17 must be submitted in electronic format (disc, email,
etc.)
• Project design shall conform to the most current edition of the International Residential Code adopted by the Commonwealth of
Pennsylvania.
• Drawings shall specify all site information such as address, lot number, TMP number, owner name and type of work Proposed. This
information
shall be reflected on all
pages.
• Drawings shall include Floor plan showing new construction in comparison to existing, room labels or use of rooms, bearing locations,
window
and door sizes, header sizes and all other pertinent information. Footing details and specifications shall be provided for all locations. Detail
should
include a footprint or outline of the scope of work as well as specifying pier or continuous footings where applicable. Pre-cast concrete panels
and
all other pre-manufactured products shall have manufacturers engineered designs and
specs.
• Insulation and thermal values shall be indicated for walls, ceiling, floors, basement walls and slab
perimeter.
• Indicate electrical components including locations and
sizes.
Swimming
Pools
• Provide swimming pools construction
specifications.
• Swimming pool enclosures and barriers shall be shown and include fence, gate and gate device
details.
Commercial Permit Application and Submittal
Requirements
The Application shall be completed as explained in the Residential information listed above.
PLANS AND SUBMITTIALS
The submittal shall include one complete set of plans and specifications bearing the signature and seal of a licensed Design Professional. Plans
and specifications shall, at minimum, be required to contain the information specified within the sections listed below.
§ 403.42a(b) A permit applicant shall submit an application to the building code official and attach construction documents, including plans and
specifications, and information concerning special inspection and structural observation programs, Department of Transportation highway access
permits and other data required by the building code official with the permit application. The applicant shall submit three sets of documents.
§ 403.42a(c) A licensed architect or licensed professional engineer shall prepare the construction documents under the Architects Licensure
Law (63 P. S. §§ 34.1-34.22), or the Engineer, Land Surveyor and Geologist Registration Law (63 P. S. §§ 148-) 58.2). An unlicensed
person
may
prepare design documents for the remodeling or alteration of a building if there is no compensation and the remodeling or alteration
does not relate to additions to the building or changes to the building's structure or means of egress.
§ 403.42a(e) The permit applicant shall submit construction documents in a format approved by the building code official. Construction documents shall
be clear, indicate the location, nature and extent of the work proposed, and show in detail that the work will conform to the Uniform Construction Code.
§ 403.42a(1) All of the following fire egress and occupancy requirements apply to construction documents:
§ 403.42a(1)(I) The permit applicant shall submit construction documents that show in sufficient detail the location, construction, size and character of
all
portio
ns of the means of egress in compliance with the Uniform Construction Code.
§ 403.42a(f)(2) The construction documents for occupancies other than Groups R-2 and R-3 shall contain designation of the number of occupants to be
accommodated on every floor and in all rooms and spaces.
§ 403.42a(f)(3) The permit applicant shall submit shop drawings for a fire protection system that indicates conformance with the Uniform Construction
Code in accordance with the following: .
§ 403.42a(f)(3)i. The shop drawings shall be approved by the building code official before the start of the system installation.
§ 403.42a(f)(3)ii The shop
dr
awings must contain the information required by the referenced installation standards contained in the " International
Building Code."
§ 403.42a(g) Construction documents shall contain the following information related to the exterior wall envelope:
§ 403.42a(g)(I) Description of the exterior wall envelope indicating compliance with the Uniform Construction Code.
§ 403.42a(g)(I) Flashing details.
§ 403.42a(g)(1) Details relating to intersections with dissimilar materials, corners, end details, control joints, intersections at roof, eaves, or parapets,
means of drainage, water-resistive membrane and details around openings.
§ 403.42a(h) Construction docum
ents shall
contain a site plan that is drawn to scale. The building code official may waive or modify the following site
plan requirements if the permit application is for an alteration or repair or if waiver or modification is warranted. Site plan requirements include all of the
following:
§ 403.42a(h)(1) The size and location of new construction and existing structures on the site.
§ 403.42a(h)(2) Accurate boundary lines.
§ 403.42a(b)(3) Distances from lot lines.
§ 403.42a(b)(4) The established street grades and the proposed finished grades.
§ 403.42a(h)(5) If the construction involves demolition, the site plan shall indicate construction that is
to be
demolished and the size and location of
existing structures and construction that will remain on the site or plot.
§ 403.42a(h)(6) Location of parking spaces, accessible routes, public transportation stops and other required accessibility features.
§ 403.42a(l) A building code official may waive or modify the submission of construction documents, that are not required to be prepared by a licensed
architect or engineer, or other data if the nature of the work applied for does not require review of construction documents or other data to obtain
compliance with the Uniform Construction Code. The building code official may not waive the submission
of site plans that relate to accessibility
requirements.
§ 403.42a(m) An applicant for an annual permit under § 403.42(f) shall complete an application and provide information regarding the system that may
be altered and the date that approval was previously provided for the approved electrical, gas, mechanical or plumbing installation.
§ 403.42a(n) A permit applicant shall comply with the permit, certification or licensure requirements of the following laws applicable to the construction:
§ 403.42a(n)(I) The Boiler and Unfired Pressure Vessel Law (35 P. S. §§ 1331 .1- 1331 .19).
§ 403.42a(n)(2) The Propane and Liquefied Petroleum Gas Act (35P. S. §§ 1329.1 - 1329.19).
§ 403.42a(0)(3) The Health Care Facilities Act.
§ 403.42a(0)(4) The Olde
r Adult Daily
Living Centers Licensing Act
Rev 3/2016 Page 4 of 4