2000 threaded port
p. 1/13www.burkert.com
The externally piloted angle-seat valve is
operated with a single or double-acting pis-
ton actuator. The actuator is available in two
different materials, PA and PPS depending
on the ambient temperature. The reliable self-
adjusting packing gland provides high sealing
integrity. High fl ow rates are attained with the
gunmetal or cast stainless steel 2-way body.
These maintenance-free and robust valves
can be retrofi tted with a comprehensive range
of accessories for position indication, stroke
limitation or manual override.
For valves with port connection clamp and
weld end please see separate datasheets.
Technical data
Orifice
DN 15 to 65
Body materials
Gunmetal, cast stainless steel 316L
Actuator material
PA or PPS
Seal material
PTFE (NBR, FKM, EPDM on request)
Medium
Water, alcohol, oils, fuel, hydraulic fl uids, salt solution,
alkali solutions, organic solvents, steam
Viscosity
max. 600 mm
2
/s
Packing gland
(with silicone grease)
PTFE V-rings with spring compensation
Medium temperature
1)
-10 to +180 ºC with PTFE seal
Ambient temperature
PA actuator
1)
PPS actuator
1)
Ø 40-80
PPS actuator
1)
Ø 100-125
-10 to +60 ºC
+5 to +140 ºC
+5 to +90 ºC, briefl y up to +140 ºC
Installation
As required, preferably with actuator in upright position
Control medium
Neutral gases, air
Max. pilot pressure
Actuator size Ø 40-80
Actuator size Ø 100
Actuator size Ø 100
Actuator size Ø 125
PA and PPS 10 bar
PA 10 bar
PPS 7 bar
PA and PPS 7 bar
Port connection
G
3/8 to G 2 1/2 (NPT on request)
1)
Note: For PA actuators in the sizes 40, 50 and 63, the
combination of max. medium temperature and max. ambi-
ent temperature is as shown in the following chart
• High flow rate
Long life cycle
• NC and NO universal actuators with modular
universal accessory program up to control heads
• Deliverable with flow direction below or above seat
• Simple conversion of the control function
2/2-way Angle-Seat Valve for
medium up to +180°C, threaded
port connection, DN 15-65
Typ 8691
Control head
Typ 8690
Pneum. control unit
with feedback
Type 1062
Electrical position
feedback
Type 8640/8644
Valve block
Type 2000 can be combined with…
Ø 40
Ø 50
Ø 63
Ambient temperature °C
Medium temperature °C












Type 6012/6014 P
Pilot valve
Valve specifi cations System spec. On/Off Classic
Request for quotation
Type 2000 threaded port Type 8801-YA/
8803-YA
Type 8801-YA/
8803-YA
Technical data & ordering info.
p. 1-7
Ordering info. & technical data
p. 8-11 p. 12
Content
2000 threaded port
p. 2/13
Materials Type 2000 threaded port
Gunmetal body Cast stainless
steel body
1
Transparent cap PC (with PPS actuator;
PSU)
PC (with PPS actuator;
PSU)
2
Pilot air ports Brass Stainless steel 1.4305
3
Actuator PA, PPS PA, PPS
4
Piston seal NBR (with PPS
actuator; FKM)
NBR (with PPS actuator;
FKM)
5
Spring Stainless steel 1.4310 Stainless steel 1.4310
6
Tube Brass
CuZn39Pb3
Stainless steel 1.4401
7
V-Seals PTFE (FKM on request) PTFE (FKM on request)
8
Wiper PTFE PTFE
9
Nipple Brass CuZn Stainless steel 1.4401
10
Spindle Stainless steel1.4021 Stainless steel 1.4401
11
Pin Stainless steel1.4401 Stainless steel 1.4401
12
Swivel plate Brass
CuZn36Pb1.5
Stainless steel 1.4401
13
Seal PTFE (NBR, FKM, EPDM
on request)
PTFE (NBR, FKM, EPDM
on request)
14
Valve body Gunmetal
GCuSn5ZnPb2%Ni
Stainless steel 316L
1
2
3
4
7
5
6
7
8
9
10
11
12
13
14
2000 threaded port
p. 3/13
Technical data Type 2000 threaded port, flow direction below seat (for gases and liquid)
Flow direction below seat
Diagram 1 Diagram 2
Pilot pressure diagram with control function B and flow direction below seat
Kv value water [m
3
/h]: Measured at +20 ºC, 1 bar pressure at valve inlet and free outlet
Pressure values [bar]: Measured as overpressure to the atmospheric pressure
16
14
12
10
8
6
4
2
0
0 1 2 3 4 5 6 7 8 9 10
Pilot pressure [bar]
Operating pressure [bar]
Actuator size
Orifice
DN15/
DN32/
DN20/
DN40/
DN25/
DN50/
DN65/
Ø50
Ø80
Ø50
Ø80
Ø50
Ø80
Ø80
16
14
12
10
8
6
4
2
0
0 1 2 3 4 5 6 7 8 9 10
Pilot pressure [bar]
Operating pressure [bar]
Actuator size
Orifice
DN25/
DN15/
DN32/
DN20/
DN40/
DN50/
Ø63
Ø40
Ø63
Ø40
Ø63
Ø63
Orifi ce Actuator
size
Kv value
water
Min. pilot
pressure
Max. operating
pressure up to ±180º
Weight
[mm] [mm] (m
3
/h) CFA [bar] CFA [bar] CFB [bar] [kg]
15 40 3.7 4.0 15 16 0.8
50 4.2 3.9 16 16 0.8
20 40 7.0 4.0 6.5 16 0.9
50 8.5 3.9 11 16 1.0
63 9.0 4.5 16 1.4
25 50 10 16 1.2
63 18 4.5 11 16 1.8
80 18 5.0 16 16 2.2
32 63 25 4.5 6 16 2.2
80 27 5.0 14 16 3.1
40 63 35 16 2.7
80 38 5.0 9 16 3.5
100 40 4.4 12.5 7.6
125 40 3.2 16 9.0
50 63 49 13 4.0
80 52 15 4.8
100 55 4.4 7.2 7.0
125 55 3.2 10 9.4
65 80 77 15 6.4
125 90 3.2 5.2 11.0
Í
2000 threaded port
p. 4/13
Ordering chart Type 2000 threaded port, flow direction below the seat (for gases and liquid)
Different actuator and body materials
Control
function
Port
connection
Orifi ce [mm]
Actuator size
Ø [mm]
Kv value water
[m
3
/h]
Minimum pilot
pressure [bar]
Max. operating
pressure up to
180 °C [bar]
Gunmetal body Cast st. st. body
Item no.
PA
actuator
Item no.
PPS
actuator
Item no.
PA
actuator
Item no.
PPS
actuator
A 2/2-way,
normally closed
(NC)
G
3/8
15
40 3.7 4.0 15 178 614 178 613 142 613 178 612
G
1/2 40 3.8 4.0 15 178 608 178 607 178 606 178 605
50 4.2 3.9 16 178 684 178 683 178 682 178 681
G
3/4 20 50 8.5 3.9 11 178 680 178 679 178 678 178 677
63 9.0 4.5 16 178 666 178 665 178 664 178 663
G 1 25 63 18 4.5 11 178 676 178 675 178 674 178 667
80 18 5.0 16 186 489 187 565 186 488 187 844
G 1
1/4 32 80 27 5.0 14 178 699 178 698 178 697 178 696
G 1
1/2 40 80 38 5.0 9 178 695 178 694 178 693 178 692
125 40 3.2 16 186 487 187 840
G 2 50 100 55.0 4.4 7.2 001 134 002 170 001 140 001 239
125 55.0 3.2 10 001 593 002 171 001 601
G 2
1/2 65 125 90.0 3.2 5.2 001 368 002 172 001 373 001 703
B 2/2-way,
normally open
(NO)
G
3/8
15
40 3.7
see diagram
1 and 2 on
previous page
16 140 368 178 610 142 616 178 609
G
1/2 40 3.8 16 178 601 178 602 178 603 178 604
50 4.2 16 178 691 178 690 178 689 178 688
G
3/4 20 50 8.5 16 178 687 179 020 178 686 178 685
G 1 25 50 10 16 178 850 178 849 178 848 178 847
G 1
1/4 32 63 25 16 178 845 178 853 178 852 178 851
G 1
1/2 40 63 35 16 178 864 178 863 178 862 178 861
G 2 50 63 49.0 13 001 371 002 179 001 376 001 709
80 52 16 001 595 002 180 001 603 002 164
G 2
1/2 65 80 77.0 15 001 372 002 181 001 377 001 710
Material
Seal: NBR, FKM, EPDM
Control function
Double-acting actuator
Port connections
Clamp, weld end (see separate datasheets)
Approvals
GL, SIL
Mediums temperature
Valves for mediums temperature up to +200ºC or down to -40ºC
&URTHERôVERSIONSôONôREQUEST
I
2000 threaded port
p. 5/13
Flow direction above seat
Technical data Type 2000 threaded port, flow direction above seat (only for gas and steam)
Attention!
Valves with fl ow direction above
the seat are only conditionally
usable for liquid medium. There
is a danger of waterhammer!
Technical data
Flow direction above seat (only for gases and steam)
Medium
Gaseous medium and steam
Further technical data
Please see information Technical data on page 1
Pilot pressure diagram with control function A and flow direction above seat
Diagram 3 Diagram 4
Kv value water [m
3
/h]: Measured at +20 ºC, 1 bar pressure at valve inlet and free outlet
Pressure values [bar]: Measured as overpressure to the atmospheric pressure
Orifi ce
[mm]
Actuator size
[mm]
Kv value water
(m
3
/h)
Max. operating
pressure
up to 180º C
Weight
[kg]
15 40 3.7 16 0.8
50 4.2 16 0.8
20 40 7.9 16 0.9
50 8.0 16 1.0
25 50 14.5 16 1.2
63 19.0 16 1.8
32 63 27.0 16 2.2
40 63 35.0 16 2.7
80 38.0 16 3.5
50 63 49.0 16 4.0
80 52.0 16 4.8
65 80 77.0 14 6.4
100 90.0 15 8.6
16
14
12
10
8
6
4
2
0
0 1 2 3 4 5 6 7 8 9 10
Pilot pressure [bar]
Operating pressure [bar]
Actuator size
Orifice
DN25/
DN15/
DN32/
DN40/
DN20/
DN65/
DN50/
Ø63
Ø40
Ø63
Ø63
Ø40
Ø100
Ø63
16
14
12
10
8
6
4
2
0
0 1 2 3 4 5 6 7 8 9 10
Pilot pressure [bar]
Operating pressure [bar]
Actuator size
Orifice
DN15/
DN20/
DN40/
DN25/
DN50/
DN65/
Ø50
Ø50
Ø80
Ø50
Ø80
Ø80
Í
2000 threaded port
p. 6/13
Control
function
Port
connection
Orifi ce [mm]
Actuator
size Ø [mm]
Kv value
water [m
3
/h]
Max. operat-
ing pressure
to 180ºC
[bar]
Gunmetal body Stainless steel body
Item no.
PA
actuator
Item no.
PPS
actuator
Item no.
PA
actuator
Item no.
PPS
actuator
A 2/2-way, normally
closed (NC)
G 3/8 15 40 3.7 16 186 588
142 615
G 1/2 50 4.2 16 183 939 186 106 186 376 186 467
G 3/4 20 40 7.9 16 186 822
187 672
50 8.0 16 185 356 180 374 185 304 180 375
G 1 25 50 14.5 16 186 380 187 556 186 729 187 872
63 18.0 16 178 860 178 859 178 857 178 856
G 1 1/4 32 63 25.0 16 178 855 178 854 178 893 178 892
G 1 1/2 40 63 35.0 16 178 896 178 897 178 895 178 894
G 2 50 63 49.0 16 001 251 002 149 001 401 002 158
G 2 1/2 65 80 77.0 14 001 398 002 151 001 402 002 160
100 90.0 15 130 332 186 344 130 333
Ordering chart Type 2000 threaded port, flow direction above the seat (only for gas and steam)
Various actuator and body materials
Minimum pilot pressure depending on operating pressure, please see diagram 3 and 4 on previous page
Material
Seal: NBR, FKM, EPDM
Control function
Double-acting actuator
Port connections
Clamp, weld end (see separate datasheets)
Approvals
GL, SIL
Mediums temperature
Valves for mediums temperature up to +200ºC or down to -40ºC
&URTHERôVERSIONSôONôREQUEST
I
on request
Valve for
actuator size
[Ø mm]
Type Pressure
inlet P
(valve body)
Service
port A
(banjo bolt)
Orifi ce
[mm]
QNn
value air
[l/min]
Pressure
range
[bar]
Electrical coil
connection
Ind. Std.
Power
consumption
[W]
Item no. Voltage/
frequency [V/Hz]
024/DC 230/50
50-63 6012P Tube fi tting ø6 mm G 1/4 1.2 48 0-10 Form B 4 552 283 552 286
40 6012P G 1/4 G 1/8 1.2 48 0-10 Form B 4 552 295 552 298
50-125 6014P G 1/4 G 1/4 2 120 0-10 Form A 8 424 103 424 107
Ordering chart for accessories
3/2-way pilot valves with banjo bolts
Seal material valve FKM, seal material banjo bolt NBR
For further accessories see datasheet for Type 1062 or the accessories datasheet Type 2XXX for the full options programme.
Item no.
Type 2507, Form B Industrial standard, 0 to 250 V without circuitry
(Type 6012 P) 423 845
Type 2508, Form A acc. DIN EN 175301-803, 0 to 250 V without circuitry
(Type 6014 P, Type 0331P) 008 376
Cable plug Type 2507, Form B or Type 2508, Form A
Note: For design reasons, some of the accessories cannot be supplied for actuator size Ø 40 mm. Please request the accessories datasheet Type 2XXX.
2000 threaded port
p. 7/13
Dimensions Type 2000 threaded port [mm]
B
E
A
D
H
F
45°
K
M
SW
Reference point
for options
P
Orifi ce Actuator
size Ø
Port
connection D
ABØ EHKMPSW
15 40 G 3/8 65 139 53 115 125 100 G 1/8 27
G 1/2 139 53 115 125 100 G 1/8
50 G 3/8 163 64 140 147 123 G 1/4
G 1/2 163 64 140 147 123 G 1/4
20 40 G 3/4 75 147 53 120 133 106 G 1/8 34
50 171 64 144 155 129 G 1/4
63 198 80 171 179 152 G 1/4
25 50 G 1 90 181 64 152 166 136 G 1/4 41
63 206 80 177 188 158 G 1/4
80 228 101 198 204 173 G 1/4
32 63 G 1 1/4 110 219 80 183 200 164 G 1/4 50
80 240 101 205 217 180 G 1/4
100 292 127 255 261 226 G 1/4
40 63 G 1 1/2 120 222 80 188 203 170 G 1/4 55
80 244 101 209 220 185 G 1/4
100 295 127 260 264 230 G 1/4
125 324 153 289 287 253 G 1/4
50 63 G 2 150 249 80 204 230 185 G 1/4 70
80 270 101 225 246 201 G 1/4
100 317 127 272 287 242 G 1/4
125 347 153 302 310 265 G 1/4
65 63 G 2 1/2 185 275 80 218 256 199 G 1/4 85
80 296 101 239 272 215 G 1/4
100 344 127 287 314 257 G 1/4
125 374 153 317 337 280 G 1/4
p. 8/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Ordering information for valve system On/Off Classic Type 8801-YA/8803-YA
A valve system On/Off Classic Type 8801-YA/8803-YA consists of an angle-seat valve Type 2000 and a valve actuation system control head Type
8691, a pneumatic control unit Type 8690 or an electrical position feedback Type 1062 (see separate datasheets).
For the confi guration of further valve systems please use the “Request for quotation” on p. 12
You order two components and receive a complete assembled and certifi ed valve.
Control units
Angle-seat valve
Type 2000 threaded port
Angle-seat valve with
desired control unit
For port connections weld end and
clamp, see separate datasheets
Valve system
On/Off Classic
Type 8803-YA
2000 + 1062
Ordering the valve system On/Off Classic Type 8801-YA/8803-YA
1062
GOôTOôPAGE
Electrical Position Feedback
Type 1062
Positions are electrically signalized according
to switch type:
- open,
- closed or
- open and closed.
LEDs provide optical position indication
(except for Namur Ex-version). Mechanical or
inductive switches are housed in a compact
splash-proof enclosure. The position indicator
can be rotated 360° and is easily fi tted to the
valve. Trip cams do not require adjustment.
The unit only needs to be screwed on and
connected to be ready for operation.
-OREô
INFO
-OREô
INFO
-OREô
INFO
When you click on the orange box "More info." below, you will come to our website for the resp. product where you can download the datasheet.
8690
(for actuator
sizes 50-125 mm
8691
(for actuator
sizes 50-125 mm
Pneumatic control unit
Type 8690
The new generation of integrated controllers
for combination with actuators from the pro-
cess valve series Type 20xx/21xx is specially
designed for the requirements of hygienic
process environments.
The pneumatic control unit Type 8690
combines electrical position feedback and
pneumatic control for single or double-acting
actuators, and is also optionally available as
an intrinsically safe model to ATEX.
Main customer benefi ts:
Integrated pilot valve with manual
actuation
Air intake fi lter enhances the process
valve system availability
Simple and reliable actuator adaptations
allowing additional actuators of the
process valve series, Type 20xx or
actuators from other manufacturers to
be used
Control head Type 8691
The new generation of integrated control
heads for combination with actuators from
the process valve series Type 20xx/21xx is
specially designed for the requirements of
hygienic process environments. The intelligent
control head, Type 8691, detects the valve
position by means of a contact-free analog
position sensor circumventing excessive wear
of mechanical parts. Single or double-acting
actuators are controlled via the integral pilot
valve. Communication interfaces AS-Interface
and DeviceNet are available as options.
Main customer benefi ts:
Automatic setting of the control head at
the push of a button
• Even under dirty or dark environments,
a clearly visible status display due to
powerful LEDs
Monitoring and diagnosis: Process valve
systems with fi eld bus interface used in
modern plant processes
Integrated pilot valve with manual
actuation
Air intake fi lter enhances the process
valve system availability
Simple and reliable actuator adaptations
allowing additional actuators of the process
valve series, Type 20xx or actuators from
other manufacturers to be used
Valve system
On/Off Classic
Type 8801-YA-K
2000 + 8690
Valve system
On/Off Classic
Type 8801-YA-H
2000 + 8691
p. 9/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Dimensions for valve system On/Off Classic Type 8801-YE-H [mm]
Dimensions valve system On/Off Classic Type 8801-YA-H with TopControl Type 8691 [mm]
Orifi ce Actuator
size
HM BM
[mm] [mm] [mm] [mm]
15 50 229 259
20 50 233 268
63 256.5 291.5
25 50 241 277
63 262.5 298.5
80 278.5 314.5
32 63 268.5 309.5
80 285.5 326.5
40 63 273.5 312.5
80 289.5 329.5
100 334.5 373.5
125 356.5 396.5
50 63 289.5 334.5
80 305.5 350.5
100 346.5 391.5
125 369.5 414.5
65 80 319.5 376.5
125 384.5 441.5
"-

(-
p. 10/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Dimensions for valve system On/Off Classic Type 8801-YE-K [mm]
Dimensions valve system On/Off Classic Type 8801-YA-K with TopControl Type 8690 [mm]
"-

(-
Orifi ce Actuator
size
HM BM
[mm] [mm] [mm] [mm]
15 50 205 235
20 50 209 244
63 233 268
25 50 217 253
63 239 275
80 254.5 290.5
32 63 245 286
80 261.5 302.5
40 63 250 289
80 265.5 305.5
100 310.5 349.5
125 332.5 372.5
50 63 266 311
80 281.5 326.5
100 322.5 367.5
125 345.5 390.5
65 80 295.5 352.5
125 360.5 417.5
p. 11/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Dimensions for valve system On/Off Classic Type 8803-YA [mm]
Dimensions valve system On/Off Classic Type 8803-YA with electrical position feedback Type 1062 [mm]
"'
('

Orifi ce
[mm]
Actuator
size ø [mm]
HG
[mm]
BG
[mm]
15 40 179 203
50 191 218
20 40 184 210
50 199 222
63 221 247
25 50 200 230
63 222 251
80 238 267
32 63 238 278
80 256 301
40 63 241 281
80 259 295
100 302 342
125 323 363
50 63 256 301
80 271 316
100 314 359
125 337 382
65 63 270 327
80 285 342
100 329 386
125 352 409
p. 12/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Operating data
= mandatory fi elds to fi ll out Quantity Required delivery date
Pipeline
Process medium
Type of medium
Liquid Steam Gas
Temperature at valve inlet
Valve features
DN PN
Company Contact person
Customer no. Department
Address Tel./Fax
Postcode/town E-Mail
Valve system On/Off Classic Type 8801-YA/8803-YA – request for quotation
Please fill out and send to your nearest Bürkert facility* with your inquiry or order
.OTE
9OUôCANôFILLôOUTô
THEôFIELDSôDIRECTLYô
INôTHEô0$&ôFILEô
BEFOREôPRINTINGô
OUTôTHEôFORM
standard unit
Flow rate (Q, Q
N, W)
1)
Absolute pressure at valve inlet
Body material
Actuator material
Stainless steel Gunmetal
PA PPS
PTFE NBR Other
Seat sealing material
Nominal pressure
PN
Nominal size
DN
Welded Internal thread Clamp
Type of connection
ISO DIN ANSI JIS Other
Standard connection
NC
2)
NO
2)
Double-acting
Function
min. max.
Pilot pressure
1)
standard unit: Liquid Q = m
3
/h; Steam W = kg/h; Gas QN = Nm
3
/h
2)
NC: normally closed by spring action; NO: normally open by spring action
Pipe material
Control unit features
Click on the orange box "More info." below... you will come to our website for the resp. product where you can download the datasheet.
continued on next page
*
Type 8691
Type 8690
Pneumatic function
Single-acting Double-acting
Without pilot valve
Position feedback
Supply voltage
1x inductive 2x inductive
1x inductive (NAMUR)
2x
inductive
(NAMUR)
1x mechanical 2x mechanical
24 V / DC (ATEX Zone 2/22)
Ex ia IIC T6 (ATEX Zone 1)
Pilot air ports
Push-in connector Thread G 1/8”
external ø 6 mm or 1/4
Pneumatic function
Single-acting Double-acting
Pilot air ports
Push-in connector external ø 6 mm or 1/4
Thread G 1/8”
Communication
ASI
Multipol M12
Flat cable clip, 1 m cable
DeviceNet
Please specify item no. if known: Please specify item no. if known:Please specify item no. if known:
Pneumatic Control Unit Control Head Electrical position feedback
-OREô
INFO
-OREô
INFO
-OREô
INFO
Type 1062
Limit switches
mechanical
Voltage 12-48 V
Voltage 110-250 V
inductive
NAMUR EExi
Status
closed
open
open/closed
Reset form
p. 13/13
2000 threaded port
System On/Off Classic
8801-YA/8803-YA
Valve system On/Off Classic Type 8801-YA/8803-YA – request for quotation, continued
Certifications
Attestation of compliance with the order EN-ISO 10204 2.1
Test report EN-ISO 10204 2.2
Certifi cation of Conformity for Raw Material EN-ISO 10204 3.1
EN161 (European Gas Device guideline)
Please specify item no. if known: Please specify item no. if known:
Power supply
Control unit features
Pilot valve
Pilot valve
Stroke limitation
Stroke limitation
Min./max. stroke limitation, with visual
position indicator
Max. stroke limitation, without visual
position indicator
Comment / sketch
Subject to Change